Take a Photo. AI Fills the Form
Your inspector takes a photo of any asset or defect. AI reads it and fills the inspection form automatically. No typing. No manual entry.
Asset & Equipment Maintenance
Compressor InspectionSoftware
Run compressor inspection in the field, capture photo evidence, log defects, assign corrective actions, and keep a complete, provable inspection history, all in one workflow.
InspectWrk is the software we provide to run this inspection workflow. It is mobile-first, offline-capable, and built so every record holds up as evidence.
Works OfflineiOS & AndroidFree Setup & Onboarding
4.5/5TrustpilotBased on 3,987 reviews
The problem this software solves
System leaks
Reported by voice or chat, system leaks is caught late and logged with no evidence tied to the asset.
Oil carry-over
Oil carry-over goes unrecorded between rounds, so there is no proof it was found, owned, or fixed.
Failed drain
On a manual round failed drain is easy to miss, and hard to defend to an auditor after the fact.
Over-pressure trips
Over-pressure trips lands in a photo thread with no owner, deadline, or audit trail behind it.
How the software solves it
InspectWrk runs the whole compressor inspection cycle on one mobile system, from the scan to the signed-off report. Here is the loop your team follows.
- 1
Inspect
Open the right compressor checklist by scanning the asset or location QR tag.
- 2
Capture
Record photos, readings, and signatures, offline where signal is poor.
- 3
Find
AI flags likely defects from the photo and the inspector confirms or overrides.
- 4
Correct
A failed item becomes an owned action with a severity and a deadline.
- 5
Verify
The finding stays open until a named approver signs off proof of the fix.
- 6
Report
A branded report generates on close-out and dashboards update across sites.
Workflow
How Does a Compressor Inspection Cycle Run from Field Capture to Audit-Ready Reporting?
The inspection workflow, end to end: Plan → Inspect → Capture evidence → Record findings → Correct → Re-inspect → Report. Every step happens on one system, so nothing falls between the field and the office.
- 1
Configure the Compressor Inspection Template
Your compressor controls become a mobile template with required photos and readings on operating pressure, oil level and leaks, dryer and drain function, safety valve, and belt or coupling condition, aligned to PSSR 2000, BS EN 1012, and PUWER 1998, so every site inspects to the same standard from day one.
- 2
Capture the Compressor Check in the Field
Inspectors complete the compressor inspection on iOS or Android, offline where signal is poor, recording pressure reading, oil sight-glass photo, and leak tag against each point before a named sign-off can close the round.
- 3
Route Compressor Findings to Verified Closure
A failed item such as system leaks becomes an owned task with a severity and a deadline, and stays open until photo proof of the fix is reviewed, so compressor defects do not resurface unnoticed.
- 4
Report Compressor Performance
Every compressor inspection feeds live dashboards and branded exports, so operations directors see completion, overdue actions, and risk per site without assembling a report by hand.
Capabilities
What the software handles for compressor inspection
The capabilities that matter for this workflow, and what your team can do with each one.
Programme Scheduling and Statutory Clocks
Every compressor inspection due date, renewal, and re-inspection sits on one calendar, so a lapsed certificate is caught before it expires, not after.
Structured Field Capture
Field teams run compressor inspection checks on a guided template that captures evidence inline, replacing loose paper and chat threads.
AI-assisted Evidence Capture
Image recognition pre-tags compressor inspection findings, so an Oil & Gas inspector spends time judging risk rather than writing it up.
Portfolio Dashboards
Operations Directors track compressor inspection risk hotspots and SLA breaches as they happen, instead of waiting for a manual Friday summary.
Audit-ready Exports
Every compressor inspection review gets a branded export and a searchable trail, so proof of what was checked is one click away.
Offline-first Mobile Apps
Weak-signal sites stop being an excuse for missing compressor inspection evidence, because capture and sync are decoupled on mobile.
Coverage
What Does a Compressor Inspection Cover?
A compressor inspection covers operating pressure, oil level and leaks, dryer and drain function, safety valve, and belt or coupling condition. Operations directors capture a photo and a reading on each compressor point. They work offline where signal is poor, then sign the compressor round off. So every compressor record proves what was checked, when, and by whom.
What Gets Checked
- Operating pressure
- Oil level and leaks
- Dryer and drain function
- Safety valve
- Belt or coupling condition
Common Defects It Surfaces
- System leaks
- Oil carry-over
- Failed drain
- Over-pressure trips
Evidence Captured
- Pressure reading
- Oil sight-glass photo
- Leak tag
Records align toPSSR 2000BS EN 1012PUWER 1998
One Platform. Mobile-First. AI-Powered.
Manage every checklist in one connected workspace, capture evidence on mobile at the point of work, and let AI turn field inputs into clear, stakeholder-ready reports in minutes.
Collaborate
Collaborate with your team anytime, anywhere
See which checklists your team has in progress across every site, jump into the same inspection with one tap, and keep field, supervisor, and back-office views in sync without sending screenshots on WhatsApp.
- Organise inspection data by site, team, and date
- Assign checks to the inspector or vendor responsible
- Track completion across every location in one view
- Keep field and back-office in sync in real time
- Comment on findings without leaving the inspection
Custom Reports
Custom reports that guide your decision making
Every team reports differently. Build the report your operations, quality, or compliance leads actually want to read, share it as a branded PDF, and schedule delivery to the stakeholders who need it.
- Branded PDF and CSV export from any completed inspection
- Schedule weekly or monthly delivery to managers and clients
- Share to email, Drive, Teams, or Slack in one click
- Filter findings by site, severity, or corrective-action status
Powerful Analytics
Analyse your inspection data with confidence
See completion, pass rate, and recurring findings across every checklist and every site, without pulling spreadsheets together at the end of the month.
AI-Powered Features for Your Field Workflows
Everything your field team does on paper, InspectWrk does automatically: faster, more accurate, and without the admin.
Speak. AI Writes It Down.
Inspectors speak their observations in any language. AI transcribes and fills the form in real time. Completely hands-free in the field.
Inspections Done. Report Ready.
The moment an inspection is submitted, a branded PDF, Excel, or CSV report generates automatically. No manual work. No waiting.
Connect Your Existing Tools.
InspectWrk integrates with the tools your team already uses, including Zoho, Microsoft 365, and SAP. No double entry.
Live Dashboard. Every Site. Always On.
Your operations team sees completion rates, open issues, and compliance scores across all sites in real time. No chasing updates.
Outcomes
What changes for your team
Operations Directors
A live view of compressor inspection status across every site, with defensible evidence and no Friday report assembly.
Field teams
Guided compressor checks on mobile with offline capture, so system leaks is caught and logged on the spot.
Compliance stakeholders
Searchable compressor history and PSSR 2000-ready exports available on demand.
Who it's for
Operations and site managers
Own performance and audit readiness across sites.
Field teams and inspectors
Complete guided checks in the field, offline where needed.
QHSE and compliance teams
Retrieve evidence the moment an auditor or client asks.
Multi-site operations leaders
Compare sites and spot recurring risk without spreadsheets.
Oil & Gas teams
Standardise on one workflow across every location.
Fits how your team already works
Your systems of record
System of record
ERP / WMS / CMMS · Existing spreadsheets · Current reporting
InspectWrk
Inspection and evidence layer
Inspections · Condition evidence · Corrective actions · Compliance clocks
Managers, clients, and auditors
Outputs
Live dashboards · Evidence packs · Audit-ready reports
Comparison
Paper and spreadsheets vs InspectWrk
Where paper and spreadsheets fall short against InspectWrk on the compressor inspection job.
| Capability | Paper / spreadsheets | With InspectWrk |
|---|---|---|
| Inspection execution | Checks like operating pressure are run on paper or from memory, so coverage and cadence vary by inspector and shift. | Guided compressor templates run the same way every time, with required fields and photos before sign-off. |
| Evidence capture | Photos sit on personal phones and in chat threads with no link to the asset or the check. | Evidence attaches to the record at the point of work, with inspector, timestamp, and location. |
| Defect identification | A fault such as system leaks is spotted late or missed entirely between rounds. | AI surfaces likely defects from the photo and the inspector confirms the finding on the spot. |
| Corrective action | Failed items are noted but ownership, deadlines, and proof of the fix are unclear. | Each failure becomes a tracked action with an owner, a due date, and photo-verified closure. |
| Reporting | Reports are assembled by hand and PSSR 2000 evidence is hard to retrieve, days after the round. | Reports generate on close-out aligned to PSSR 2000, and managers see status across every site live. |
Rollout
How Should Oil & Gas Teams Pilot Compressor Inspection Digitally Without Disrupting Operations?
Pilot on one site cluster
Pick one oil & gas cluster for the initial compressor inspection rollout, confirm the dashboards match what the field sees, then extend template by template.
Scale templates and roles
Roll compressor inspection out site by site, granting contractors scoped access and tying templates to the specific oil & gas obligations each location carries.
Connect reporting and integrations
Publish compressor inspection performance to portfolio dashboards, export branded audit packs, and integrate with the oil & gas systems that own work orders and records.
Before You Switch
Common Questions Before You Start
We already run compressor checks on paper. Do we have to change our process?
No. Your existing checklist becomes a mobile template, so the same checks run with photos, timestamps, and named sign-off attached. Only the capture changes.
Will field teams actually use it?
The check runs on the device they already carry, works offline where signal drops, and opens the right checklist from a QR scan, so there is no typing from memory.
What happens when a defect is found?
It becomes an owned action with a severity and a deadline, and stays open until a named approver verifies the fix with photo proof.
Reviews From Real People
4.5/5TrustpilotBased on 3,987 reviews
What our
customers are
saying
“InspectWrk transformed how we manage site safety inspections. The offline capability alone saved us countless hours. Our compliance rate jumped from 72% to 96% in just three months.”
Sarah Mitchell
Meridian Construction Group
“The AI-powered defect detection has changed how we work. Our inspectors capture photos and the system flags issues we'd have missed. It's like having an expert reviewer on every site visit.”
James Chen
Pacific Manufacturing Co.
“Rolling out digital checklists across multiple projects gave us instant visibility into recurring safety issues. We now resolve critical findings in hours instead of days.”
Olivia Carter
Northbridge Infrastructure
Ready to Move Compressor Inspection Off Paper?
Inspections Across Industries
View All
Which Compressor Inspection Checklist Templates Should You Try First?
Get started with inspection and audit checklist templates.
Energy Management
ENERGY STAR Benchmarking Checklist
Prepare and validate an ENERGY STAR benchmarking submission: property and building information, reporting period, utility and meter data, electricity and fuel consumption, data completeness and validation, Portfolio Manager entry and review, and recordkeeping.
8,800+GET
Template
Drilling Rig Daily Safety Checklist
Use this Drilling Rig Daily safety check to verify critical checkpoints and safety controls, compliance records and sign-off and corrective actions with photo evidence on energy…
500+GET
Which Compressor Inspection Apps Run on iOS and Android?
Use these apps to run inspections and audits.
Frequently Asked Questions About Compressor Inspection Software
What does Compressor Inspection Software check on a compressor inspection?
Compressor Inspection Software runs a structured compressor inspection covering operating pressure, oil level and leaks, dryer and drain function, safety valve, and belt or coupling condition. Each point is captured on mobile with a photo and a reading, and a named inspector signs the round off before it can close. The same template runs on every site, so operations directors work to one standard rather than a version that drifts between locations. Every record proves what was checked, when, and by whom, so the evidence is ready long before an assessor asks for it.
How often should a compressor inspection be done?
How often compressor checks run depends on duty, risk, and the standard you follow. Some are daily or pre-use; others run weekly, monthly, or at a statutory interval. Compressor Inspection Software sets the cadence per site, reminds operations directors before a round is due, and flags anything overdue automatically. Each completed round is timestamped and signed, so the schedule is provably kept rather than assumed, and you can show exactly when the last check happened for any asset. Operations Directors run compressor inspections on a phone or tablet with Compressor Inspection Software, keeping one record for each compressor and site.
Which compressor defects matter most, and what happens if they are missed?
The inspection targets the compressor failures that matter most: system leaks, oil carry-over, failed drain, and over-pressure trips. Left unchecked, a fault such as system leaks can mean downtime, a safety incident, or a failed audit, so every finding becomes an owned task with a deadline. It stays open until photo proof of the repair is reviewed, and repeat problems are flagged so operations directors fix the cause rather than the symptom. Prioritising by severity means the most serious issues are handled first, not whichever was reported loudest.
Which standards does Compressor Inspection Software support for compressor work?
Compressor Inspection Software keeps compressor checks aligned to PSSR 2000, BS EN 1012, and PUWER 1998. The photos and readings each standard expects are required fields, so an incomplete check cannot be closed and a gap is caught before an assessor finds it. When a review is due, operations directors export a branded evidence pack built from pressure reading, oil sight-glass photo, and leak tag, ready to hand over on the spot. Retention and history stay searchable, so proof remains defensible at any point, not only on the day of an audit.
Can teams run compressor checks offline and across multiple sites?
Yes. Compressor Inspection Software is offline-first: teams complete compressor checks on iOS or Android with no signal, capturing pressure reading, oil sight-glass photo, and leak tag in the field. Each record syncs automatically when the connection returns, with its timestamp intact, and the same template runs on every site. So operations directors get a live view of what is complete, overdue, or failing per location, and a weak connection in a plant room or basement never costs a round or loses a photo.
What evidence proves a compressor inspection was completed?
Every completed compressor inspection carries pressure reading, oil sight-glass photo, and leak tag, a GPS location, a timestamp, and a named sign-off. Because the evidence is captured during the round rather than typed up afterwards, operations directors can show exactly what was checked, when, and by whom. When an assessor or client asks, the record exports in seconds as a branded PDF or a searchable history, so proof never depends on someone remembering where a photo was saved or which folder holds last quarter's records.
Last updated: