Take a Photo. AI Fills the Form
Your inspector takes a photo of any asset or defect. AI reads it and fills the inspection form automatically. No typing. No manual entry.
Fleet & Transport
Forklift InspectionSoftware
Run forklift inspection in the field, capture photo evidence, log defects, assign corrective actions, and keep a complete, provable inspection history, all in one workflow.
InspectWrk is the software we provide to run this inspection workflow. It is mobile-first, offline-capable, and built so every record holds up as evidence.
Works OfflineiOS & AndroidFree Setup & Onboarding
4.5/5TrustpilotBased on 3,987 reviews
The problem this software solves
Fork damage
Reported by voice or chat, fork damage is caught late and logged with no evidence tied to the asset.
Brake fade
Brake fade goes unrecorded between rounds, so there is no proof it was found, owned, or fixed.
Hydraulic weep
On a manual round hydraulic weep is easy to miss, and hard to defend to an auditor after the fact.
Inoperative horn
Inoperative horn lands in a photo thread with no owner, deadline, or audit trail behind it.
How the software solves it
InspectWrk runs the whole forklift inspection cycle on one mobile system, from the scan to the signed-off report. Here is the loop your team follows.
- 1
Inspect
Open the right forklift checklist by scanning the asset or location QR tag.
- 2
Capture
Record photos, readings, and signatures, offline where signal is poor.
- 3
Find
AI flags likely defects from the photo and the inspector confirms or overrides.
- 4
Correct
A failed item becomes an owned action with a severity and a deadline.
- 5
Verify
The finding stays open until a named approver signs off proof of the fix.
- 6
Report
A branded report generates on close-out and dashboards update across sites.
Workflow
How Does a Forklift Inspection Cycle Run from Field Capture to Audit-Ready Reporting?
The inspection workflow, end to end: Plan → Inspect → Capture evidence → Record findings → Correct → Re-inspect → Report. Every step happens on one system, so nothing falls between the field and the office.
- 1
Configure the Forklift Inspection Template
Your forklift controls become a mobile template with required photos and readings on mast and forks, hydraulic leaks, tyres and brakes, horn and lights, and load backrest, aligned to ISO 45001 and OSHA forklift standards, so every site inspects to the same standard from day one.
- 2
Capture the Forklift Check in the Field
Inspectors complete the forklift inspection on iOS or Android, offline where signal is poor, recording pre-use photo of defect and hour-meter reading against each point before a named sign-off can close the round.
- 3
Route Forklift Findings to Verified Closure
A failed item such as fork damage becomes an owned task with a severity and a deadline, and stays open until photo proof of the fix is reviewed, so forklift defects do not resurface unnoticed.
- 4
Report Forklift Performance
Every forklift inspection feeds live dashboards and branded exports, so operations directors see completion, overdue actions, and risk per site without assembling a report by hand.
Capabilities
What the software handles for forklift inspection
The capabilities that matter for this workflow, and what your team can do with each one.
Programme Scheduling and Statutory Clocks
Every forklift inspection due date, renewal, and re-inspection sits on one calendar, so a lapsed certificate is caught before it expires, not after.
Structured Field Capture
Where forklift inspection evidence has to hold up, field teams run forklift inspection checks on a guided template that captures evidence inline, replacing loose paper and chat threads.
AI-assisted Evidence Capture
On-device AI flags likely defects in forklift inspection photos and pre-fills findings, so inspectors type less and miss less in the field.
Portfolio Dashboards
Operations Directors see forklift inspection completion, overdue actions, and risk hotspots across the Transport & Logistics portfolio without assembling a report.
Audit-ready Exports
Forklift Inspection evidence exports as a regulator-ready pack with photos and sign-offs intact, filtered to the site under review.
Offline-first Mobile Apps
Weak-signal sites stop being an excuse for missing forklift inspection evidence, because capture and sync are decoupled on mobile.
Coverage
What Does a Forklift Inspection Cover?
A forklift inspection covers mast and forks, hydraulic leaks, tyres and brakes, horn and lights, and load backrest. Operations directors capture a photo and a reading on each forklift point. They work offline where signal is poor, then sign the forklift round off. So every forklift record proves what was checked, when, and by whom.
What Gets Checked
- Mast and forks
- Hydraulic leaks
- Tyres and brakes
- Horn and lights
- Load backrest
Common Defects It Surfaces
- Fork damage
- Brake fade
- Hydraulic weep
- Inoperative horn
Evidence Captured
- Pre-use photo of defect
- Hour-meter reading
Records align toISO 45001OSHA forklift standards
One Platform. Mobile-First. AI-Powered.
Manage every checklist in one connected workspace, capture evidence on mobile at the point of work, and let AI turn field inputs into clear, stakeholder-ready reports in minutes.
Collaborate
Collaborate with your team anytime, anywhere
See which checklists your team has in progress across every site, jump into the same inspection with one tap, and keep field, supervisor, and back-office views in sync without sending screenshots on WhatsApp.
- Organise inspection data by site, team, and date
- Assign checks to the inspector or vendor responsible
- Track completion across every location in one view
- Keep field and back-office in sync in real time
- Comment on findings without leaving the inspection
Custom Reports
Custom reports that guide your decision making
Every team reports differently. Build the report your operations, quality, or compliance leads actually want to read, share it as a branded PDF, and schedule delivery to the stakeholders who need it.
- Branded PDF and CSV export from any completed inspection
- Schedule weekly or monthly delivery to managers and clients
- Share to email, Drive, Teams, or Slack in one click
- Filter findings by site, severity, or corrective-action status
Powerful Analytics
Analyse your inspection data with confidence
See completion, pass rate, and recurring findings across every checklist and every site, without pulling spreadsheets together at the end of the month.
AI-Powered Features for Your Field Workflows
Everything your field team does on paper, InspectWrk does automatically: faster, more accurate, and without the admin.
Speak. AI Writes It Down.
Inspectors speak their observations in any language. AI transcribes and fills the form in real time. Completely hands-free in the field.
Inspections Done. Report Ready.
The moment an inspection is submitted, a branded PDF, Excel, or CSV report generates automatically. No manual work. No waiting.
Connect Your Existing Tools.
InspectWrk integrates with the tools your team already uses, including Zoho, Microsoft 365, and SAP. No double entry.
Live Dashboard. Every Site. Always On.
Your operations team sees completion rates, open issues, and compliance scores across all sites in real time. No chasing updates.
Outcomes
What changes for your team
Operations Directors
A live view of forklift inspection status across every site, with defensible evidence and no Friday report assembly.
Field teams
Guided forklift checks on mobile with offline capture, so fork damage is caught and logged on the spot.
Compliance stakeholders
Searchable forklift history and ISO 45001-ready exports available on demand.
Who it's for
Operations and site managers
Own performance and audit readiness across sites.
Field teams and inspectors
Complete guided checks in the field, offline where needed.
QHSE and compliance teams
Retrieve evidence the moment an auditor or client asks.
Multi-site operations leaders
Compare sites and spot recurring risk without spreadsheets.
Transport & Logistics teams
Standardise on one workflow across every location.
Fits how your team already works
Your systems of record
System of record
ERP / WMS / CMMS · Existing spreadsheets · Current reporting
InspectWrk
Inspection and evidence layer
Inspections · Condition evidence · Corrective actions · Compliance clocks
Managers, clients, and auditors
Outputs
Live dashboards · Evidence packs · Audit-ready reports
Comparison
Paper and spreadsheets vs InspectWrk
Where paper and spreadsheets fall short against InspectWrk on the forklift inspection job.
| Capability | Paper / spreadsheets | With InspectWrk |
|---|---|---|
| Inspection execution | Checks like mast and forks are run on paper or from memory, so coverage and cadence vary by inspector and shift. | Guided forklift templates run the same way every time, with required fields and photos before sign-off. |
| Evidence capture | Photos sit on personal phones and in chat threads with no link to the asset or the check. | Evidence attaches to the record at the point of work, with inspector, timestamp, and location. |
| Defect identification | A fault such as fork damage is spotted late or missed entirely between rounds. | AI surfaces likely defects from the photo and the inspector confirms the finding on the spot. |
| Corrective action | Failed items are noted but ownership, deadlines, and proof of the fix are unclear. | Each failure becomes a tracked action with an owner, a due date, and photo-verified closure. |
| Reporting | Reports are assembled by hand and ISO 45001 evidence is hard to retrieve, days after the round. | Reports generate on close-out aligned to ISO 45001, and managers see status across every site live. |
Rollout
How Should Transport & Logistics Teams Pilot Forklift Inspection Digitally Without Disrupting Operations?
Pilot on one site cluster
Begin with one forklift inspection template on a single cluster of transport & logistics sites, then read completion rates and closure times before you widen the rollout.
Scale templates and roles
Scale the forklift inspection programme by cloning the proven template, then adjust it to local transport & logistics rules so every site inspects to one standard.
Connect reporting and integrations
Feed forklift inspection results into portfolio dashboards and branded exports, and push findings to your CMMS, ERP, or GRC stack through the API where transport & logistics teams need it.
Before You Switch
Common Questions Before You Start
We already run forklift checks on paper. Do we have to change our process?
No. Your existing checklist becomes a mobile template, so the same checks run with photos, timestamps, and named sign-off attached. Only the capture changes.
Will field teams actually use it?
The check runs on the device they already carry, works offline where signal drops, and opens the right checklist from a QR scan, so there is no typing from memory.
What happens when a defect is found?
It becomes an owned action with a severity and a deadline, and stays open until a named approver verifies the fix with photo proof.
Reviews From Real People
4.5/5TrustpilotBased on 3,987 reviews
What our
customers are
saying
“InspectWrk transformed how we manage site safety inspections. The offline capability alone saved us countless hours. Our compliance rate jumped from 72% to 96% in just three months.”
Sarah Mitchell
Meridian Construction Group
“The AI-powered defect detection has changed how we work. Our inspectors capture photos and the system flags issues we'd have missed. It's like having an expert reviewer on every site visit.”
James Chen
Pacific Manufacturing Co.
“Rolling out digital checklists across multiple projects gave us instant visibility into recurring safety issues. We now resolve critical findings in hours instead of days.”
Olivia Carter
Northbridge Infrastructure
Ready to Move Forklift Inspection Off Paper?
Inspections Across Industries
View All
Which Forklift Inspection Checklist Templates Should You Try First?
Get started with inspection and audit checklist templates.
Template
Light Vehicle Safety Inspection
Use this template to perform a comprehensive safety inspection of light vehicles. This check ensures all critical components are checked ...
500+GET
Which Forklift Inspection Apps Run on iOS and Android?
Use these apps to run inspections and audits.
Frequently Asked Questions About Forklift Inspection Software
What does Forklift Inspection Software check on a forklift inspection?
Forklift Inspection Software runs a structured forklift inspection covering mast and forks, hydraulic leaks, tyres and brakes, horn and lights, and load backrest. Each point is captured on mobile with a photo and a reading, and a named inspector signs the round off before it can close. The same template runs on every site, so operations directors work to one standard rather than a version that drifts between locations. Every record proves what was checked, when, and by whom, so the evidence is ready long before an assessor asks for it.
How often should a forklift inspection be done?
How often forklift checks run depends on duty, risk, and the standard you follow. Some are daily or pre-use; others run weekly, monthly, or at a statutory interval. Forklift Inspection Software sets the cadence per site, reminds operations directors before a round is due, and flags anything overdue automatically. Each completed round is timestamped and signed, so the schedule is provably kept rather than assumed, and you can show exactly when the last check happened for any asset. In transport & logistics, Forklift Inspection Software turns approved forklift checklists into mobile checks field teams complete on any device.
Which forklift defects matter most, and what happens if they are missed?
The inspection targets the forklift failures that matter most: fork damage, brake fade, hydraulic weep, and inoperative horn. Left unchecked, a fault such as fork damage can mean downtime, a safety incident, or a failed audit, so every finding becomes an owned task with a deadline. It stays open until photo proof of the repair is reviewed, and repeat problems are flagged so operations directors fix the cause rather than the symptom. Prioritising by severity means the most serious issues are handled first, not whichever was reported loudest.
Which standards does Forklift Inspection Software support for forklift work?
Forklift Inspection Software keeps forklift checks aligned to ISO 45001 and OSHA forklift standards. The photos and readings each standard expects are required fields, so an incomplete check cannot be closed and a gap is caught before an assessor finds it. When a review is due, operations directors export a branded evidence pack built from pre-use photo of defect and hour-meter reading, ready to hand over on the spot. Retention and history stay searchable, so proof remains defensible at any point, not only on the day of an audit.
Can teams run forklift checks offline and across multiple sites?
Yes. Forklift Inspection Software is offline-first: teams complete forklift checks on iOS or Android with no signal, capturing pre-use photo of defect and hour-meter reading in the field. Each record syncs automatically when the connection returns, with its timestamp intact, and the same template runs on every site. So operations directors get a live view of what is complete, overdue, or failing per location, and a weak connection in a plant room or basement never costs a round or loses a photo.
What evidence proves a forklift inspection was completed?
Every completed forklift inspection carries pre-use photo of defect and hour-meter reading, a GPS location, a timestamp, and a named sign-off. Because the evidence is captured during the round rather than typed up afterwards, operations directors can show exactly what was checked, when, and by whom. When an assessor or client asks, the record exports in seconds as a branded PDF or a searchable history, so proof never depends on someone remembering where a photo was saved or which folder holds last quarter's records.
Last updated: