Take a Photo. AI Fills the Form
Your inspector takes a photo of any asset or defect. AI reads it and fills the inspection form automatically. No typing. No manual entry.
Oil & Gas
Offshore InspectionSoftware
Run offshore inspection in the field, capture photo evidence, log defects, assign corrective actions, and keep a complete, provable inspection history, all in one workflow.
InspectWrk is the software we provide to run this inspection workflow. It is mobile-first, offline-capable, and built so every record holds up as evidence.
Works OfflineiOS & AndroidFree Setup & Onboarding
4.5/5TrustpilotBased on 3,987 reviews
The problem this software solves
Structural corrosion
Reported by voice or chat, structural corrosion is caught late and logged with no evidence tied to the asset.
Safety-critical element failure
Safety-critical element failure goes unrecorded between rounds, so there is no proof it was found, owned, or fixed.
Lifeboat or escape fault
On a manual round lifeboat or escape fault is easy to miss, and hard to defend to an auditor after the fact.
Fire and gas detection fault
Fire and gas detection fault lands in a photo thread with no owner, deadline, or audit trail behind it.
How the software solves it
InspectWrk runs the whole offshore inspection cycle on one mobile system, from the scan to the signed-off report. Here is the loop your team follows.
- 1
Inspect
Open the right offshore checklist by scanning the asset or location QR tag.
- 2
Capture
Record photos, readings, and signatures, offline where signal is poor.
- 3
Find
AI flags likely defects from the photo and the inspector confirms or overrides.
- 4
Correct
A failed item becomes an owned action with a severity and a deadline.
- 5
Verify
The finding stays open until a named approver signs off proof of the fix.
- 6
Report
A branded report generates on close-out and dashboards update across sites.
Workflow
How Does an Offshore Inspection Cycle Run from Field Capture to Audit-Ready Reporting?
The inspection workflow, end to end: Plan → Inspect → Capture evidence → Record findings → Correct → Re-inspect → Report. Every step happens on one system, so nothing falls between the field and the office.
- 1
Configure the Offshore Inspection Template
Your offshore controls become a mobile template with required photos and readings on structural integrity and corrosion, safety-critical elements, lifeboats and escape systems, fire and gas detection, and permit to work and isolation, aligned to offshore safety case and SEMS, so every site inspects to the same standard from day one.
- 2
Capture the Offshore Check in the Field
Inspectors complete the offshore inspection on iOS or Android, offline where signal is poor, recording sce test record, corrosion photo, and muster and drill note against each point before a named sign-off can close the round.
- 3
Route Offshore Findings to Verified Closure
A failed item such as structural corrosion becomes an owned task with a severity and a deadline, and stays open until photo proof of the fix is reviewed, so offshore defects do not resurface unnoticed.
- 4
Report Offshore Performance
On every offshore inspection cycle, every offshore inspection feeds live dashboards and branded exports, so operations directors see completion, overdue actions, and risk per site without assembling a report by hand.
Capabilities
What the software handles for offshore inspection
The capabilities that matter for this workflow, and what your team can do with each one.
Programme Scheduling and Statutory Clocks
Statutory and SLA clocks for offshore inspection run automatically, giving Operations Directors a live view of what is due, overdue, and signed off.
Structured Field Capture
Across multi-site offshore inspection rounds, structured offshore inspection forms force the photo, reading, and sign-off before an item can close, so partial records never ship.
AI-assisted Evidence Capture
Where offshore inspection evidence has to hold up, AI photo review turns offshore inspection evidence into draft findings on the spot, which the inspector accepts, edits, or rejects.
Portfolio Dashboards
On every offshore inspection cycle, offshore Inspection performance rolls up live by site and region, so Operations Directors brief leadership from data rather than anecdote.
Audit-ready Exports
For Oil & Gas teams running offshore inspection, searchable offshore inspection records mean any past check is retrievable instantly, so Operations Directors stop rebuilding history from drives.
Offline-first Mobile Apps
In Oil & Gas offshore inspection operations, iOS and Android apps cache offshore inspection templates and submissions, so basements, plant rooms, and remote sites never block capture.
Coverage
What Does an Offshore Inspection Cover?
An offshore inspection covers structural integrity and corrosion, safety-critical elements, lifeboats and escape systems, fire and gas detection, and permit to work and isolation. Operations directors capture a photo and a reading on each offshore point. They work offline where signal is poor, then sign the offshore round off. So every offshore record proves what was checked, when, and by whom.
What Gets Checked
- Structural integrity and corrosion
- Safety-critical elements
- Lifeboats and escape systems
- Fire and gas detection
- Permit to work and isolation
Common Defects It Surfaces
- Structural corrosion
- Safety-critical element failure
- Lifeboat or escape fault
- Fire and gas detection fault
- Permit lapse
Evidence Captured
- SCE test record
- Corrosion photo
- Muster and drill note
Records align tooffshore safety caseSEMS
One Platform. Mobile-First. AI-Powered.
Manage every checklist in one connected workspace, capture evidence on mobile at the point of work, and let AI turn field inputs into clear, stakeholder-ready reports in minutes.
Collaborate
Collaborate with your team anytime, anywhere
See which checklists your team has in progress across every site, jump into the same inspection with one tap, and keep field, supervisor, and back-office views in sync without sending screenshots on WhatsApp.
- Organise inspection data by site, team, and date
- Assign checks to the inspector or vendor responsible
- Track completion across every location in one view
- Keep field and back-office in sync in real time
- Comment on findings without leaving the inspection
Custom Reports
Custom reports that guide your decision making
Every team reports differently. Build the report your operations, quality, or compliance leads actually want to read, share it as a branded PDF, and schedule delivery to the stakeholders who need it.
- Branded PDF and CSV export from any completed inspection
- Schedule weekly or monthly delivery to managers and clients
- Share to email, Drive, Teams, or Slack in one click
- Filter findings by site, severity, or corrective-action status
Powerful Analytics
Analyse your inspection data with confidence
See completion, pass rate, and recurring findings across every checklist and every site, without pulling spreadsheets together at the end of the month.
AI-Powered Features for Your Field Workflows
Everything your field team does on paper, InspectWrk does automatically: faster, more accurate, and without the admin.
Speak. AI Writes It Down.
Inspectors speak their observations in any language. AI transcribes and fills the form in real time. Completely hands-free in the field.
Inspections Done. Report Ready.
The moment an inspection is submitted, a branded PDF, Excel, or CSV report generates automatically. No manual work. No waiting.
Connect Your Existing Tools.
InspectWrk integrates with the tools your team already uses, including Zoho, Microsoft 365, and SAP. No double entry.
Live Dashboard. Every Site. Always On.
Your operations team sees completion rates, open issues, and compliance scores across all sites in real time. No chasing updates.
Outcomes
What changes for your team
Operations Directors
A live view of offshore inspection status across every site, with defensible evidence and no Friday report assembly.
Field teams
Guided offshore checks on mobile with offline capture, so structural corrosion is caught and logged on the spot.
Compliance stakeholders
Searchable offshore history and offshore safety case-ready exports available on demand.
Who it's for
Operations and site managers
Own performance and audit readiness across sites.
Field teams and inspectors
Complete guided checks in the field, offline where needed.
QHSE and compliance teams
Retrieve evidence the moment an auditor or client asks.
Multi-site operations leaders
Compare sites and spot recurring risk without spreadsheets.
Oil & Gas teams
Standardise on one workflow across every location.
Fits how your team already works
Your systems of record
System of record
ERP / WMS / CMMS · Existing spreadsheets · Current reporting
InspectWrk
Inspection and evidence layer
Inspections · Condition evidence · Corrective actions · Compliance clocks
Managers, clients, and auditors
Outputs
Live dashboards · Evidence packs · Audit-ready reports
Comparison
Paper and spreadsheets vs InspectWrk
Where paper and spreadsheets fall short against InspectWrk on the offshore inspection job.
| Capability | Paper / spreadsheets | With InspectWrk |
|---|---|---|
| Inspection execution | Checks like structural integrity and corrosion are run on paper or from memory, so coverage and cadence vary by inspector and shift. | Guided offshore templates run the same way every time, with required fields and photos before sign-off. |
| Evidence capture | Photos sit on personal phones and in chat threads with no link to the asset or the check. | Evidence attaches to the record at the point of work, with inspector, timestamp, and location. |
| Defect identification | A fault such as structural corrosion is spotted late or missed entirely between rounds. | AI surfaces likely defects from the photo and the inspector confirms the finding on the spot. |
| Corrective action | Failed items are noted but ownership, deadlines, and proof of the fix are unclear. | Each failure becomes a tracked action with an owner, a due date, and photo-verified closure. |
| Reporting | Reports are assembled by hand and offshore safety case evidence is hard to retrieve, days after the round. | Reports generate on close-out aligned to offshore safety case, and managers see status across every site live. |
Rollout
How Should Oil & Gas Teams Pilot Offshore Inspection Digitally Without Disrupting Operations?
Pilot on one site cluster
Start narrow with a pilot offshore inspection programme on a few sites, so Operations Directors can validate evidence quality and correction speed against the old paper baseline.
Scale templates and roles
Extend offshore inspection access to contractors and in-house crews with role-based permissions, and map each template to your oil & gas standards and statutory duties.
Connect reporting and integrations
Feed offshore inspection results into portfolio dashboards and branded exports, and push findings to your CMMS, ERP, or GRC stack through the API where oil & gas teams need it.
Before You Switch
Common Questions Before You Start
We already run offshore checks on paper. Do we have to change our process?
No. Your existing checklist becomes a mobile template, so the same checks run with photos, timestamps, and named sign-off attached. Only the capture changes.
Will field teams actually use it?
The check runs on the device they already carry, works offline where signal drops, and opens the right checklist from a QR scan, so there is no typing from memory.
What happens when a defect is found?
It becomes an owned action with a severity and a deadline, and stays open until a named approver verifies the fix with photo proof.
Reviews From Real People
4.5/5TrustpilotBased on 3,987 reviews
What our
customers are
saying
“InspectWrk transformed how we manage site safety inspections. The offline capability alone saved us countless hours. Our compliance rate jumped from 72% to 96% in just three months.”
Sarah Mitchell
Meridian Construction Group
“The AI-powered defect detection has changed how we work. Our inspectors capture photos and the system flags issues we'd have missed. It's like having an expert reviewer on every site visit.”
James Chen
Pacific Manufacturing Co.
“Rolling out digital checklists across multiple projects gave us instant visibility into recurring safety issues. We now resolve critical findings in hours instead of days.”
Olivia Carter
Northbridge Infrastructure
Ready to Move Offshore Inspection Off Paper?
Inspections Across Industries
View All
Which Offshore Inspection Checklist Templates Should You Try First?
Get started with inspection and audit checklist templates.
Energy Management
ENERGY STAR Benchmarking Checklist
Prepare and validate an ENERGY STAR benchmarking submission: property and building information, reporting period, utility and meter data, electricity and fuel consumption, data completeness and validation, Portfolio Manager entry and review, and recordkeeping.
8,800+GET
Template
Drilling Rig Daily Safety Checklist
Use this Drilling Rig Daily safety check to verify critical checkpoints and safety controls, compliance records and sign-off and corrective actions with photo evidence on energy…
500+GET
Which Offshore Inspection Apps Run on iOS and Android?
Use these apps to run inspections and audits.
Frequently Asked Questions About Offshore Inspection Software
What does Offshore Inspection Software check on an offshore inspection?
Offshore Inspection Software runs a structured offshore inspection covering structural integrity and corrosion, safety-critical elements, lifeboats and escape systems, fire and gas detection, and permit to work and isolation. Each point is captured on mobile with a photo and a reading, and a named inspector signs the round off before it can close. The same template runs on every site, so operations directors work to one standard rather than a version that drifts between locations. Every record proves what was checked, when, and by whom, so the evidence is ready long before an assessor asks for it.
How often should an offshore inspection be done?
How often offshore checks run depends on duty, risk, and the standard you follow. Some are daily or pre-use; others run weekly, monthly, or at a statutory interval. Offshore Inspection Software sets the cadence per site, reminds operations directors before a round is due, and flags anything overdue automatically. Each completed round is timestamped and signed, so the schedule is provably kept rather than assumed, and you can show exactly when the last check happened for any asset. Operations Directors run offshore inspections on a phone or tablet with Offshore Inspection Software, keeping one record for each offshore and site.
Which offshore defects matter most, and what happens if they are missed?
The inspection targets the offshore failures that matter most: structural corrosion, safety-critical element failure, lifeboat or escape fault, and fire and gas detection fault. Left unchecked, a fault such as structural corrosion can mean downtime, a safety incident, or a failed audit, so every finding becomes an owned task with a deadline. It stays open until photo proof of the repair is reviewed, and repeat problems are flagged so operations directors fix the cause rather than the symptom. Prioritising by severity means the most serious issues are handled first, not whichever was reported loudest.
Which standards does Offshore Inspection Software support for offshore work?
Offshore Inspection Software keeps offshore checks aligned to offshore safety case and SEMS. The photos and readings each standard expects are required fields, so an incomplete check cannot be closed and a gap is caught before an assessor finds it. When a review is due, operations directors export a branded evidence pack built from sce test record, corrosion photo, and muster and drill note, ready to hand over on the spot. Retention and history stay searchable, so proof remains defensible at any point, not only on the day of an audit.
Can teams run offshore checks offline and across multiple sites?
Yes. Offshore Inspection Software is offline-first: teams complete offshore checks on iOS or Android with no signal, capturing sce test record, corrosion photo, and muster and drill note in the field. Each record syncs automatically when the connection returns, with its timestamp intact, and the same template runs on every site. So operations directors get a live view of what is complete, overdue, or failing per location, and a weak connection in a plant room or basement never costs a round or loses a photo.
What evidence proves an offshore inspection was completed?
Every completed offshore inspection carries sce test record, corrosion photo, and muster and drill note, a GPS location, a timestamp, and a named sign-off. Because the evidence is captured during the round rather than typed up afterwards, operations directors can show exactly what was checked, when, and by whom. When an assessor or client asks, the record exports in seconds as a branded PDF or a searchable history, so proof never depends on someone remembering where a photo was saved or which folder holds last quarter's records.
Last updated: