Take a Photo. AI Fills the Form
Your inspector takes a photo of any asset or defect. AI reads it and fills the inspection form automatically. No typing. No manual entry.
Safety & Compliance
Permit to Work InspectionSoftware
Run permit to work inspection in the field, capture photo evidence, log defects, assign corrective actions, and keep a complete, provable inspection history, all in one workflow.
InspectWrk is the software we provide to run this inspection workflow. It is mobile-first, offline-capable, and built so every record holds up as evidence.
Works OfflineiOS & AndroidFree Setup & Onboarding
4.5/5TrustpilotBased on 3,987 reviews
The problem this software solves
Expired or missing PTW
Reported by voice or chat, expired or missing PTW is caught late and logged with no evidence tied to the asset.
Incomplete LOTO
Incomplete LOTO goes unrecorded between rounds, so there is no proof it was found, owned, or fixed.
Open edges
On a manual round open edges is easy to miss, and hard to defend to an auditor after the fact.
Unattended hot work
Unattended hot work lands in a photo thread with no owner, deadline, or audit trail behind it.
How the software solves it
InspectWrk runs the whole permit to work inspection cycle on one mobile system, from the scan to the signed-off report. Here is the loop your team follows.
- 1
Inspect
Open the right permit to work checklist by scanning the asset or location QR tag.
- 2
Capture
Record photos, readings, and signatures, offline where signal is poor.
- 3
Find
AI flags likely defects from the photo and the inspector confirms or overrides.
- 4
Correct
A failed item becomes an owned action with a severity and a deadline.
- 5
Verify
The finding stays open until a named approver signs off proof of the fix.
- 6
Report
A branded report generates on close-out and dashboards update across sites.
Workflow
How Does a Permit to Work Inspection Cycle Run from Field Capture to Audit-Ready Reporting?
The inspection workflow, end to end: Plan → Inspect → Capture evidence → Record findings → Correct → Re-inspect → Report. Every step happens on one system, so nothing falls between the field and the office.
- 1
Configure the Permit Work Inspection Template
Your permit work controls become a mobile template with required photos and readings on permit-to-work currency, LOTO isolation points, edge protection and ladder condition, confined-space atmosphere and attendant, and hot-work fire watch and combustibles, aligned to ISO 45001, OSHA 1926, and local PTW rules, so every site inspects to the same standard from day one.
- 2
Capture the Permit Work Check in the Field
Inspectors complete the permit work inspection on iOS or Android, offline where signal is poor, recording permit photo, isolation tag photo, and edge protection photo against each point before a named sign-off can close the round.
- 3
Route Permit Work Findings to Verified Closure
A failed item such as expired or missing PTW becomes an owned task with a severity and a deadline, and stays open until photo proof of the fix is reviewed, so permit work defects do not resurface unnoticed.
- 4
Report Permit Work Performance
Every permit work inspection feeds live dashboards and branded exports, so operations directors see completion, overdue actions, and risk per site without assembling a report by hand.
Capabilities
What the software handles for permit to work inspection
The capabilities that matter for this workflow, and what your team can do with each one.
Programme Scheduling and Statutory Clocks
In Oil & Gas permit to work inspection operations, permit To Work Inspection cadence is enforced per asset: the next check is booked the moment the last one closes, so nothing silently slips off the plan.
Structured Field Capture
Across the permit to work inspection portfolio, field teams run permit to work inspection checks on a guided template that captures evidence inline, replacing loose paper and chat threads.
AI-assisted Evidence Capture
On permit to work inspection programmes, on-device AI flags likely defects in permit to work inspection photos and pre-fills findings, so inspectors type less and miss less in the field.
Portfolio Dashboards
For permit to work inspection field teams, operations Directors see permit to work inspection completion, overdue actions, and risk hotspots across the Oil & Gas portfolio without assembling a report.
Audit-ready Exports
Across multi-site permit to work inspection rounds, every permit to work inspection review gets a branded export and a searchable trail, so proof of what was checked is one click away.
Offline-first Mobile Apps
Where permit to work inspection evidence has to hold up, weak-signal sites stop being an excuse for missing permit to work inspection evidence, because capture and sync are decoupled on mobile.
Coverage
What Does a Permit Work Inspection Cover?
A permit work inspection covers permit-to-work currency, LOTO isolation points, edge protection and ladder condition, confined-space atmosphere and attendant, and hot-work fire watch and combustibles. Operations directors capture a photo and a reading on each permit work point. They work offline where signal is poor, then sign the permit work round off. So every permit work record proves what was checked, when, and by whom.
What Gets Checked
- Permit-to-work currency
- LOTO isolation points
- Edge protection and ladder condition
- Confined-space atmosphere and attendant
- Hot-work fire watch and combustibles
Common Defects It Surfaces
- Expired or missing PTW
- Incomplete LOTO
- Open edges
- Unattended hot work
Evidence Captured
- Permit photo
- Isolation tag photo
- Edge protection photo
Records align toISO 45001OSHA 1926local PTW rules
One Platform. Mobile-First. AI-Powered.
Manage every checklist in one connected workspace, capture evidence on mobile at the point of work, and let AI turn field inputs into clear, stakeholder-ready reports in minutes.
Collaborate
Collaborate with your team anytime, anywhere
See which checklists your team has in progress across every site, jump into the same inspection with one tap, and keep field, supervisor, and back-office views in sync without sending screenshots on WhatsApp.
- Organise inspection data by site, team, and date
- Assign checks to the inspector or vendor responsible
- Track completion across every location in one view
- Keep field and back-office in sync in real time
- Comment on findings without leaving the inspection
Custom Reports
Custom reports that guide your decision making
Every team reports differently. Build the report your operations, quality, or compliance leads actually want to read, share it as a branded PDF, and schedule delivery to the stakeholders who need it.
- Branded PDF and CSV export from any completed inspection
- Schedule weekly or monthly delivery to managers and clients
- Share to email, Drive, Teams, or Slack in one click
- Filter findings by site, severity, or corrective-action status
Powerful Analytics
Analyse your inspection data with confidence
See completion, pass rate, and recurring findings across every checklist and every site, without pulling spreadsheets together at the end of the month.
AI-Powered Features for Your Field Workflows
Everything your field team does on paper, InspectWrk does automatically: faster, more accurate, and without the admin.
Speak. AI Writes It Down.
Inspectors speak their observations in any language. AI transcribes and fills the form in real time. Completely hands-free in the field.
Inspections Done. Report Ready.
The moment an inspection is submitted, a branded PDF, Excel, or CSV report generates automatically. No manual work. No waiting.
Connect Your Existing Tools.
InspectWrk integrates with the tools your team already uses, including Zoho, Microsoft 365, and SAP. No double entry.
Live Dashboard. Every Site. Always On.
Your operations team sees completion rates, open issues, and compliance scores across all sites in real time. No chasing updates.
Outcomes
What changes for your team
Operations Directors
A live view of permit work inspection status across every site, with defensible evidence and no Friday report assembly.
Field teams
Guided permit work checks on mobile with offline capture, so expired or missing PTW is caught and logged on the spot.
Compliance stakeholders
Searchable permit work history and ISO 45001-ready exports available on demand.
Who it's for
Operations and site managers
Own performance and audit readiness across sites.
Field teams and inspectors
Complete guided checks in the field, offline where needed.
QHSE and compliance teams
Retrieve evidence the moment an auditor or client asks.
Multi-site operations leaders
Compare sites and spot recurring risk without spreadsheets.
Oil & Gas teams
Standardise on one workflow across every location.
Fits how your team already works
Your systems of record
System of record
ERP / WMS / CMMS · Existing spreadsheets · Current reporting
InspectWrk
Inspection and evidence layer
Inspections · Condition evidence · Corrective actions · Compliance clocks
Managers, clients, and auditors
Outputs
Live dashboards · Evidence packs · Audit-ready reports
Comparison
Paper and spreadsheets vs InspectWrk
Where paper and spreadsheets fall short against InspectWrk on the permit to work inspection job.
| Capability | Paper / spreadsheets | With InspectWrk |
|---|---|---|
| Inspection execution | Checks like permit-to-work currency are run on paper or from memory, so coverage and cadence vary by inspector and shift. | Guided permit to work templates run the same way every time, with required fields and photos before sign-off. |
| Evidence capture | Photos sit on personal phones and in chat threads with no link to the asset or the check. | Evidence attaches to the record at the point of work, with inspector, timestamp, and location. |
| Defect identification | A fault such as expired or missing PTW is spotted late or missed entirely between rounds. | AI surfaces likely defects from the photo and the inspector confirms the finding on the spot. |
| Corrective action | Failed items are noted but ownership, deadlines, and proof of the fix are unclear. | Each failure becomes a tracked action with an owner, a due date, and photo-verified closure. |
| Reporting | Reports are assembled by hand and ISO 45001 evidence is hard to retrieve, days after the round. | Reports generate on close-out aligned to ISO 45001, and managers see status across every site live. |
Rollout
How Should Oil & Gas Teams Pilot Permit to Work Inspection Digitally Without Disrupting Operations?
Pilot on one site cluster
Run the first permit to work inspection cycle on one site cluster and compare it to your current process on capture speed, evidence completeness, and overdue actions before scaling.
Scale templates and roles
As more oil & gas sites come on, give each role the permit to work inspection views they need and align every template to the codes Operations Directors answer for.
Connect reporting and integrations
Turn on live permit to work inspection reporting for Operations Directors, and route readings and defects into the CMMS or compliance system of record so nothing is re-keyed.
Before You Switch
Common Questions Before You Start
We already run permit to work checks on paper. Do we have to change our process?
No. Your existing checklist becomes a mobile template, so the same checks run with photos, timestamps, and named sign-off attached. Only the capture changes.
Will field teams actually use it?
The check runs on the device they already carry, works offline where signal drops, and opens the right checklist from a QR scan, so there is no typing from memory.
What happens when a defect is found?
It becomes an owned action with a severity and a deadline, and stays open until a named approver verifies the fix with photo proof.
Reviews From Real People
4.5/5TrustpilotBased on 3,987 reviews
What our
customers are
saying
“InspectWrk transformed how we manage site safety inspections. The offline capability alone saved us countless hours. Our compliance rate jumped from 72% to 96% in just three months.”
Sarah Mitchell
Meridian Construction Group
“The AI-powered defect detection has changed how we work. Our inspectors capture photos and the system flags issues we'd have missed. It's like having an expert reviewer on every site visit.”
James Chen
Pacific Manufacturing Co.
“Rolling out digital checklists across multiple projects gave us instant visibility into recurring safety issues. We now resolve critical findings in hours instead of days.”
Olivia Carter
Northbridge Infrastructure
Ready to Move Permit to Work Inspection Off Paper?
Inspections Across Industries
View All
Which Permit to Work Inspection Checklist Templates Should You Try First?
Get started with inspection and audit checklist templates.
Energy Management
ENERGY STAR Benchmarking Checklist
Prepare and validate an ENERGY STAR benchmarking submission: property and building information, reporting period, utility and meter data, electricity and fuel consumption, data completeness and validation, Portfolio Manager entry and review, and recordkeeping.
8,800+GET
Template
Drilling Rig Daily Safety Checklist
Use this Drilling Rig Daily safety check to verify critical checkpoints and safety controls, compliance records and sign-off and corrective actions with photo evidence on energy…
500+GET
Which Permit to Work Inspection Apps Run on iOS and Android?
Use these apps to run inspections and audits.
Frequently Asked Questions About Permit to Work Inspection Software
What does Permit To Work Inspection Software check on a permit work inspection?
Permit To Work Inspection Software runs a structured permit work inspection covering permit-to-work currency, LOTO isolation points, edge protection and ladder condition, confined-space atmosphere and attendant, and hot-work fire watch and combustibles. Each point is captured on mobile with a photo and a reading, and a named inspector signs the round off before it can close. The same template runs on every site, so operations directors work to one standard rather than a version that drifts between locations. Every record proves what was checked, when, and by whom, so the evidence is ready long before an assessor asks for it.
How often should a permit work inspection be done?
How often permit work checks run depends on duty, risk, and the standard you follow. Some are daily or pre-use; others run weekly, monthly, or at a statutory interval. Permit To Work Inspection Software sets the cadence per site, reminds operations directors before a round is due, and flags anything overdue automatically. Each completed round is timestamped and signed, so the schedule is provably kept rather than assumed, and you can show exactly when the last check happened for any asset.
Which permit work defects matter most, and what happens if they are missed?
The inspection targets the permit work failures that matter most: expired or missing PTW, incomplete LOTO, open edges, and unattended hot work. Left unchecked, a fault such as expired or missing PTW can mean downtime, a safety incident, or a failed audit, so every finding becomes an owned task with a deadline. It stays open until photo proof of the repair is reviewed, and repeat problems are flagged so operations directors fix the cause rather than the symptom. Prioritising by severity means the most serious issues are handled first, not whichever was reported loudest.
Which standards does Permit To Work Inspection Software support for permit work?
Permit To Work Inspection Software keeps permit work checks aligned to ISO 45001, OSHA 1926, and local PTW rules. The photos and readings each standard expects are required fields, so an incomplete check cannot be closed and a gap is caught before an assessor finds it. When a review is due, operations directors export a branded evidence pack built from permit photo, isolation tag photo, and edge protection photo, ready to hand over on the spot. Retention and history stay searchable, so proof remains defensible at any point, not only on the day of an audit.
Can teams run permit work checks offline and across multiple sites?
Yes. Permit To Work Inspection Software is offline-first: teams complete permit work checks on iOS or Android with no signal, capturing permit photo, isolation tag photo, and edge protection photo in the field. Each record syncs automatically when the connection returns, with its timestamp intact, and the same template runs on every site. So operations directors get a live view of what is complete, overdue, or failing per location, and a weak connection in a plant room or basement never costs a round or loses a photo.
What evidence proves a permit work inspection was completed?
Every completed permit work inspection carries permit photo, isolation tag photo, and edge protection photo, a GPS location, a timestamp, and a named sign-off. Because the evidence is captured during the round rather than typed up afterwards, operations directors can show exactly what was checked, when, and by whom. When an assessor or client asks, the record exports in seconds as a branded PDF or a searchable history, so proof never depends on someone remembering where a photo was saved or which folder holds last quarter's records.
Last updated: