Take a Photo. AI Fills the Form
Your inspector takes a photo of any asset or defect. AI reads it and fills the inspection form automatically. No typing. No manual entry.
Construction
Formwork InspectionSoftware
Run formwork inspection in the field, capture photo evidence, log defects, assign corrective actions, and keep a complete, provable inspection history, all in one workflow.
InspectWrk is the software we provide to run this inspection workflow. It is mobile-first, offline-capable, and built so every record holds up as evidence.
Works OfflineiOS & AndroidFree Setup & Onboarding
4.5/5TrustpilotBased on 3,987 reviews
The problem this software solves
Undersized or missing props
Reported by voice or chat, undersized or missing props is caught late and logged with no evidence tied to the asset.
Inadequate bracing
Inadequate bracing goes unrecorded between rounds, so there is no proof it was found, owned, or fixed.
Out-of-level decking
On a manual round out-of-level decking is easy to miss, and hard to defend to an auditor after the fact.
Grout loss at joints
Grout loss at joints lands in a photo thread with no owner, deadline, or audit trail behind it.
How the software solves it
InspectWrk runs the whole formwork inspection cycle on one mobile system, from the scan to the signed-off report. Here is the loop your team follows.
- 1
Inspect
Open the right formwork checklist by scanning the asset or location QR tag.
- 2
Capture
Record photos, readings, and signatures, offline where signal is poor.
- 3
Find
AI flags likely defects from the photo and the inspector confirms or overrides.
- 4
Correct
A failed item becomes an owned action with a severity and a deadline.
- 5
Verify
The finding stays open until a named approver signs off proof of the fix.
- 6
Report
A branded report generates on close-out and dashboards update across sites.
Workflow
How Does a Formwork Inspection Cycle Run from Field Capture to Audit-Ready Reporting?
The inspection workflow, end to end: Plan → Inspect → Capture evidence → Record findings → Correct → Re-inspect → Report. Every step happens on one system, so nothing falls between the field and the office.
- 1
Configure the Formwork Inspection Template
Your formwork controls become a mobile template with required photos and readings on props, spacing, and bracing, bearers, joists, and decking, verticality, line, and level, release agent and cleanliness, and edge protection and access, aligned to BS 5975 and OSHA 1926 subpart Q, so every site inspects to the same standard from day one.
- 2
Capture the Formwork Check in the Field
Inspectors complete the formwork inspection on iOS or Android, offline where signal is poor, recording prop layout photo, level check note, and pre-pour permit against each point before a named sign-off can close the round.
- 3
Route Formwork Findings to Verified Closure
A failed item such as undersized or missing props becomes an owned task with a severity and a deadline, and stays open until photo proof of the fix is reviewed, so formwork defects do not resurface unnoticed.
- 4
Report Formwork Performance
Every formwork inspection feeds live dashboards and branded exports, so site managers see completion, overdue actions, and risk per site without assembling a report by hand.
Capabilities
What the software handles for formwork inspection
The capabilities that matter for this workflow, and what your team can do with each one.
Programme Scheduling and Statutory Clocks
Formwork Inspection cadence is enforced per asset: the next check is booked the moment the last one closes, so nothing silently slips off the plan.
Structured Field Capture
Field teams run formwork inspection checks on a guided template that captures evidence inline, replacing loose paper and chat threads.
AI-assisted Evidence Capture
On-device AI flags likely defects in formwork inspection photos and pre-fills findings, so inspectors type less and miss less in the field.
Portfolio Dashboards
One screen shows every site's formwork inspection status, so Site Managers spot the failing location before it becomes a Construction incident.
Audit-ready Exports
Branded PDF packs and searchable formwork inspection history assemble Construction audit evidence for clients, insurers, and regulators in minutes.
Offline-first Mobile Apps
Weak-signal sites stop being an excuse for missing formwork inspection evidence, because capture and sync are decoupled on mobile.
Coverage
What Does a Formwork Inspection Cover?
A formwork inspection covers props, spacing, and bracing, bearers, joists, and decking, verticality, line, and level, release agent and cleanliness, and edge protection and access. Site managers capture a photo and a reading on each formwork point. They work offline where signal is poor, then sign the formwork round off. So every formwork record proves what was checked, when, and by whom.
What Gets Checked
- Props, spacing, and bracing
- Bearers, joists, and decking
- Verticality, line, and level
- Release agent and cleanliness
- Edge protection and access
Common Defects It Surfaces
- Undersized or missing props
- Inadequate bracing
- Out-of-level decking
- Grout loss at joints
- Missing edge protection
Evidence Captured
- Prop layout photo
- Level check note
- Pre-pour permit
Records align toBS 5975OSHA 1926 subpart Q
One Platform. Mobile-First. AI-Powered.
Manage every checklist in one connected workspace, capture evidence on mobile at the point of work, and let AI turn field inputs into clear, stakeholder-ready reports in minutes.
Collaborate
Collaborate with your team anytime, anywhere
See which checklists your team has in progress across every site, jump into the same inspection with one tap, and keep field, supervisor, and back-office views in sync without sending screenshots on WhatsApp.
- Organise inspection data by site, team, and date
- Assign checks to the inspector or vendor responsible
- Track completion across every location in one view
- Keep field and back-office in sync in real time
- Comment on findings without leaving the inspection
Custom Reports
Custom reports that guide your decision making
Every team reports differently. Build the report your operations, quality, or compliance leads actually want to read, share it as a branded PDF, and schedule delivery to the stakeholders who need it.
- Branded PDF and CSV export from any completed inspection
- Schedule weekly or monthly delivery to managers and clients
- Share to email, Drive, Teams, or Slack in one click
- Filter findings by site, severity, or corrective-action status
Powerful Analytics
Analyse your inspection data with confidence
See completion, pass rate, and recurring findings across every checklist and every site, without pulling spreadsheets together at the end of the month.
AI-Powered Features for Your Field Workflows
Everything your field team does on paper, InspectWrk does automatically: faster, more accurate, and without the admin.
Speak. AI Writes It Down.
Inspectors speak their observations in any language. AI transcribes and fills the form in real time. Completely hands-free in the field.
Inspections Done. Report Ready.
The moment an inspection is submitted, a branded PDF, Excel, or CSV report generates automatically. No manual work. No waiting.
Connect Your Existing Tools.
InspectWrk integrates with the tools your team already uses, including Zoho, Microsoft 365, and SAP. No double entry.
Live Dashboard. Every Site. Always On.
Your operations team sees completion rates, open issues, and compliance scores across all sites in real time. No chasing updates.
Outcomes
What changes for your team
Site Managers
A live view of formwork inspection status across every site, with defensible evidence and no Friday report assembly.
Field teams
Guided formwork checks on mobile with offline capture, so undersized or missing props is caught and logged on the spot.
Compliance stakeholders
Searchable formwork history and BS 5975-ready exports available on demand.
Who it's for
Operations and site managers
Own performance and audit readiness across sites.
Field teams and inspectors
Complete guided checks in the field, offline where needed.
QHSE and compliance teams
Retrieve evidence the moment an auditor or client asks.
Multi-site operations leaders
Compare sites and spot recurring risk without spreadsheets.
Construction teams
Standardise on one workflow across every location.
Fits how your team already works
Your systems of record
System of record
ERP / WMS / CMMS · Existing spreadsheets · Current reporting
InspectWrk
Inspection and evidence layer
Inspections · Condition evidence · Corrective actions · Compliance clocks
Managers, clients, and auditors
Outputs
Live dashboards · Evidence packs · Audit-ready reports
Comparison
Paper and spreadsheets vs InspectWrk
Where paper and spreadsheets fall short against InspectWrk on the formwork inspection job.
| Capability | Paper / spreadsheets | With InspectWrk |
|---|---|---|
| Inspection execution | Checks like props, spacing, and bracing are run on paper or from memory, so coverage and cadence vary by inspector and shift. | Guided formwork templates run the same way every time, with required fields and photos before sign-off. |
| Evidence capture | Photos sit on personal phones and in chat threads with no link to the asset or the check. | Evidence attaches to the record at the point of work, with inspector, timestamp, and location. |
| Defect identification | A fault such as undersized or missing props is spotted late or missed entirely between rounds. | AI surfaces likely defects from the photo and the inspector confirms the finding on the spot. |
| Corrective action | Failed items are noted but ownership, deadlines, and proof of the fix are unclear. | Each failure becomes a tracked action with an owner, a due date, and photo-verified closure. |
| Reporting | Reports are assembled by hand and BS 5975 evidence is hard to retrieve, days after the round. | Reports generate on close-out aligned to BS 5975, and managers see status across every site live. |
Rollout
How Should Construction Teams Pilot Formwork Inspection Digitally Without Disrupting Operations?
Pilot on one site cluster
Begin with one formwork inspection template on a single cluster of construction sites, then read completion rates and closure times before you widen the rollout.
Scale templates and roles
Scale the formwork inspection programme by cloning the proven template, then adjust it to local construction rules so every site inspects to one standard.
Connect reporting and integrations
Wire formwork inspection data into leadership dashboards and share-ready PDFs, then connect the API to the asset register or maintenance system your construction operation already runs.
Before You Switch
Common Questions Before You Start
We already run formwork checks on paper. Do we have to change our process?
No. Your existing checklist becomes a mobile template, so the same checks run with photos, timestamps, and named sign-off attached. Only the capture changes.
Will field teams actually use it?
The check runs on the device they already carry, works offline where signal drops, and opens the right checklist from a QR scan, so there is no typing from memory.
What happens when a defect is found?
It becomes an owned action with a severity and a deadline, and stays open until a named approver verifies the fix with photo proof.
Reviews From Real People
4.5/5TrustpilotBased on 3,987 reviews
What our
customers are
saying
“InspectWrk transformed how we manage site safety inspections. The offline capability alone saved us countless hours. Our compliance rate jumped from 72% to 96% in just three months.”
Sarah Mitchell
Meridian Construction Group
“The AI-powered defect detection has changed how we work. Our inspectors capture photos and the system flags issues we'd have missed. It's like having an expert reviewer on every site visit.”
James Chen
Pacific Manufacturing Co.
“Rolling out digital checklists across multiple projects gave us instant visibility into recurring safety issues. We now resolve critical findings in hours instead of days.”
Olivia Carter
Northbridge Infrastructure
Ready to Move Formwork Inspection Off Paper?
Inspections Across Industries
View All
Which Formwork Inspection Checklist Templates Should You Try First?
Get started with inspection and audit checklist templates.
Snagging / Punch List
Snagging Inspection Checklist
Catch defects before handover and generate punch list reports in minutes. Room-by-room finish checks, evidence, and corrective actions.
52,000+GET
Snagging / Punch List
New Build Apartment Snagging Checklist
Pre-handover snagging for new build apartments. Room-by-room finish checks, MEP, and defect tracking before keys.
28,500+GET
Safety Inspection
Scaffolding Inspection Checklist
Utilize this Scaffolding Safety Inspection Checklist to spot hazards, verify stability, and ensure compliance with safety standards before work begins.
19,800+GET
Service Report
Field Service Report Form
Capture job details, measurements, work performed, photos, and sign-offs in one structured field service report form.
14,200+GET
Which Formwork Inspection Apps Run on iOS and Android?
Use these apps to run inspections and audits.
Frequently Asked Questions About Formwork Inspection Software
What does Formwork Inspection Software check on a formwork inspection?
Formwork Inspection Software runs a structured formwork inspection covering props, spacing, and bracing, bearers, joists, and decking, verticality, line, and level, release agent and cleanliness, and edge protection and access. Each point is captured on mobile with a photo and a reading, and a named inspector signs the round off before it can close. The same template runs on every site, so site managers work to one standard rather than a version that drifts between locations. Every record proves what was checked, when, and by whom, so the evidence is ready long before an assessor asks for it.
How often should a formwork inspection be done?
How often formwork checks run depends on duty, risk, and the standard you follow. Some are daily or pre-use; others run weekly, monthly, or at a statutory interval. Formwork Inspection Software sets the cadence per site, reminds site managers before a round is due, and flags anything overdue automatically. Each completed round is timestamped and signed, so the schedule is provably kept rather than assumed, and you can show exactly when the last check happened for any asset. Site Managers run formwork inspections on a phone or tablet with Formwork Inspection Software, keeping one record for each formwork and site.
Which formwork defects matter most, and what happens if they are missed?
The inspection targets the formwork failures that matter most: undersized or missing props, inadequate bracing, out-of-level decking, and grout loss at joints. Left unchecked, a fault such as undersized or missing props can mean downtime, a safety incident, or a failed audit, so every finding becomes an owned task with a deadline. It stays open until photo proof of the repair is reviewed, and repeat problems are flagged so site managers fix the cause rather than the symptom. Prioritising by severity means the most serious issues are handled first, not whichever was reported loudest.
Which standards does Formwork Inspection Software support for formwork work?
Formwork Inspection Software keeps formwork checks aligned to BS 5975 and OSHA 1926 subpart Q. The photos and readings each standard expects are required fields, so an incomplete check cannot be closed and a gap is caught before an assessor finds it. When a review is due, site managers export a branded evidence pack built from prop layout photo, level check note, and pre-pour permit, ready to hand over on the spot. Retention and history stay searchable, so proof remains defensible at any point, not only on the day of an audit.
Can teams run formwork checks offline and across multiple sites?
Yes. Formwork Inspection Software is offline-first: teams complete formwork checks on iOS or Android with no signal, capturing prop layout photo, level check note, and pre-pour permit in the field. Each record syncs automatically when the connection returns, with its timestamp intact, and the same template runs on every site. So site managers get a live view of what is complete, overdue, or failing per location, and a weak connection in a plant room or basement never costs a round or loses a photo.
What evidence proves a formwork inspection was completed?
Every completed formwork inspection carries prop layout photo, level check note, and pre-pour permit, a GPS location, a timestamp, and a named sign-off. Because the evidence is captured during the round rather than typed up afterwards, site managers can show exactly what was checked, when, and by whom. When an assessor or client asks, the record exports in seconds as a branded PDF or a searchable history, so proof never depends on someone remembering where a photo was saved or which folder holds last quarter's records.
Last updated: