Take a Photo. AI Fills the Form
Your inspector takes a photo of any asset or defect. AI reads it and fills the inspection form automatically. No typing. No manual entry.
Inspection & Field Operations
Structural InspectionSoftware
Run structural inspection in the field, capture photo evidence, log defects, assign corrective actions, and keep a complete, provable inspection history, all in one workflow.
InspectWrk is the software we provide to run this inspection workflow. It is mobile-first, offline-capable, and built so every record holds up as evidence.
Works OfflineiOS & AndroidFree Setup & Onboarding
4.5/5TrustpilotBased on 3,987 reviews
The problem this software solves
Under-torqued or missing bolts
Reported by voice or chat, under-torqued or missing bolts is caught late and logged with no evidence tied to the asset.
Weld defects
Weld defects goes unrecorded between rounds, so there is no proof it was found, owned, or fixed.
Member out of plumb
On a manual round member out of plumb is easy to miss, and hard to defend to an auditor after the fact.
Missing temporary bracing
Missing temporary bracing lands in a photo thread with no owner, deadline, or audit trail behind it.
How the software solves it
InspectWrk runs the whole structural inspection cycle on one mobile system, from the scan to the signed-off report. Here is the loop your team follows.
- 1
Inspect
Open the right structural checklist by scanning the asset or location QR tag.
- 2
Capture
Record photos, readings, and signatures, offline where signal is poor.
- 3
Find
AI flags likely defects from the photo and the inspector confirms or overrides.
- 4
Correct
A failed item becomes an owned action with a severity and a deadline.
- 5
Verify
The finding stays open until a named approver signs off proof of the fix.
- 6
Report
A branded report generates on close-out and dashboards update across sites.
Workflow
How Does a Structural Inspection Cycle Run from Field Capture to Audit-Ready Reporting?
The inspection workflow, end to end: Plan → Inspect → Capture evidence → Record findings → Correct → Re-inspect → Report. Every step happens on one system, so nothing falls between the field and the office.
- 1
Configure the Structural Inspection Template
Your structural controls become a mobile template with required photos and readings on connections, bolts, and welds, member alignment and plumb, temporary bracing and stability, bearing and baseplate grouting, and corrosion protection, aligned to AISC 360, BS EN 1090, and IS 800, so every site inspects to the same standard from day one.
- 2
Capture the Structural Check in the Field
Inspectors complete the structural inspection on iOS or Android, offline where signal is poor, recording bolt and weld photo, plumb and alignment note, and erection sign-off against each point before a named sign-off can close the round.
- 3
Route Structural Findings to Verified Closure
A failed item such as under-torqued or missing bolts becomes an owned task with a severity and a deadline, and stays open until photo proof of the fix is reviewed, so structural defects do not resurface unnoticed.
- 4
Report Structural Performance
Every structural inspection feeds live dashboards and branded exports, so site managers see completion, overdue actions, and risk per site without assembling a report by hand.
Capabilities
What the software handles for structural inspection
The capabilities that matter for this workflow, and what your team can do with each one.
Programme Scheduling and Statutory Clocks
Structural Inspection scheduling ties each renewal to its asset and owner, so Construction cycles stay defensible without a manual tracker.
Structured Field Capture
Required-field structural inspection capture means no skipped questions and no missing evidence, even when the round is rushed.
AI-assisted Evidence Capture
AI assists structural inspection capture by reading photos for common faults, so field teams confirm rather than transcribe.
Portfolio Dashboards
Site Managers see structural inspection completion, overdue actions, and risk hotspots across the Construction portfolio without assembling a report.
Audit-ready Exports
Structural Inspection evidence exports as a regulator-ready pack with photos and sign-offs intact, filtered to the site under review.
Offline-first Mobile Apps
Weak-signal sites stop being an excuse for missing structural inspection evidence, because capture and sync are decoupled on mobile.
Coverage
What Does a Structural Inspection Cover?
A structural inspection covers connections, bolts, and welds, member alignment and plumb, temporary bracing and stability, bearing and baseplate grouting, and corrosion protection. Site managers capture a photo and a reading on each structural point. They work offline where signal is poor, then sign the structural round off. So every structural record proves what was checked, when, and by whom.
What Gets Checked
- Connections, bolts, and welds
- Member alignment and plumb
- Temporary bracing and stability
- Bearing and baseplate grouting
- Corrosion protection
Common Defects It Surfaces
- Under-torqued or missing bolts
- Weld defects
- Member out of plumb
- Missing temporary bracing
- Ungrouted baseplate
Evidence Captured
- Bolt and weld photo
- Plumb and alignment note
- Erection sign-off
Records align toAISC 360BS EN 1090IS 800
One Platform. Mobile-First. AI-Powered.
Manage every checklist in one connected workspace, capture evidence on mobile at the point of work, and let AI turn field inputs into clear, stakeholder-ready reports in minutes.
Collaborate
Collaborate with your team anytime, anywhere
See which checklists your team has in progress across every site, jump into the same inspection with one tap, and keep field, supervisor, and back-office views in sync without sending screenshots on WhatsApp.
- Organise inspection data by site, team, and date
- Assign checks to the inspector or vendor responsible
- Track completion across every location in one view
- Keep field and back-office in sync in real time
- Comment on findings without leaving the inspection
Custom Reports
Custom reports that guide your decision making
Every team reports differently. Build the report your operations, quality, or compliance leads actually want to read, share it as a branded PDF, and schedule delivery to the stakeholders who need it.
- Branded PDF and CSV export from any completed inspection
- Schedule weekly or monthly delivery to managers and clients
- Share to email, Drive, Teams, or Slack in one click
- Filter findings by site, severity, or corrective-action status
Powerful Analytics
Analyse your inspection data with confidence
See completion, pass rate, and recurring findings across every checklist and every site, without pulling spreadsheets together at the end of the month.
AI-Powered Features for Your Field Workflows
Everything your field team does on paper, InspectWrk does automatically: faster, more accurate, and without the admin.
Speak. AI Writes It Down.
Inspectors speak their observations in any language. AI transcribes and fills the form in real time. Completely hands-free in the field.
Inspections Done. Report Ready.
The moment an inspection is submitted, a branded PDF, Excel, or CSV report generates automatically. No manual work. No waiting.
Connect Your Existing Tools.
InspectWrk integrates with the tools your team already uses, including Zoho, Microsoft 365, and SAP. No double entry.
Live Dashboard. Every Site. Always On.
Your operations team sees completion rates, open issues, and compliance scores across all sites in real time. No chasing updates.
Outcomes
What changes for your team
Site Managers
A live view of structural inspection status across every site, with defensible evidence and no Friday report assembly.
Field teams
Guided structural checks on mobile with offline capture, so under-torqued or missing bolts is caught and logged on the spot.
Compliance stakeholders
Searchable structural history and AISC 360-ready exports available on demand.
Who it's for
Operations and site managers
Own performance and audit readiness across sites.
Field teams and inspectors
Complete guided checks in the field, offline where needed.
QHSE and compliance teams
Retrieve evidence the moment an auditor or client asks.
Multi-site operations leaders
Compare sites and spot recurring risk without spreadsheets.
Construction teams
Standardise on one workflow across every location.
Fits how your team already works
Your systems of record
System of record
ERP / WMS / CMMS · Existing spreadsheets · Current reporting
InspectWrk
Inspection and evidence layer
Inspections · Condition evidence · Corrective actions · Compliance clocks
Managers, clients, and auditors
Outputs
Live dashboards · Evidence packs · Audit-ready reports
Comparison
Paper and spreadsheets vs InspectWrk
Where paper and spreadsheets fall short against InspectWrk on the structural inspection job.
| Capability | Paper / spreadsheets | With InspectWrk |
|---|---|---|
| Inspection execution | Checks like connections, bolts, and welds are run on paper or from memory, so coverage and cadence vary by inspector and shift. | Guided structural templates run the same way every time, with required fields and photos before sign-off. |
| Evidence capture | Photos sit on personal phones and in chat threads with no link to the asset or the check. | Evidence attaches to the record at the point of work, with inspector, timestamp, and location. |
| Defect identification | A fault such as under-torqued or missing bolts is spotted late or missed entirely between rounds. | AI surfaces likely defects from the photo and the inspector confirms the finding on the spot. |
| Corrective action | Failed items are noted but ownership, deadlines, and proof of the fix are unclear. | Each failure becomes a tracked action with an owner, a due date, and photo-verified closure. |
| Reporting | Reports are assembled by hand and AISC 360 evidence is hard to retrieve, days after the round. | Reports generate on close-out aligned to AISC 360, and managers see status across every site live. |
Rollout
How Should Construction Teams Pilot Structural Inspection Digitally Without Disrupting Operations?
Pilot on one site cluster
Prove the structural inspection workflow on one region first, checking that findings close on time and audit packs assemble cleanly before the next site group joins.
Scale templates and roles
Widen structural inspection coverage across the estate with permissions per role and templates that reflect each construction site's regulatory scope.
Connect reporting and integrations
Feed structural inspection results into portfolio dashboards and branded exports, and push findings to your CMMS, ERP, or GRC stack through the API where construction teams need it.
Before You Switch
Common Questions Before You Start
We already run structural checks on paper. Do we have to change our process?
No. Your existing checklist becomes a mobile template, so the same checks run with photos, timestamps, and named sign-off attached. Only the capture changes.
Will field teams actually use it?
The check runs on the device they already carry, works offline where signal drops, and opens the right checklist from a QR scan, so there is no typing from memory.
What happens when a defect is found?
It becomes an owned action with a severity and a deadline, and stays open until a named approver verifies the fix with photo proof.
Reviews From Real People
4.5/5TrustpilotBased on 3,987 reviews
What our
customers are
saying
“InspectWrk transformed how we manage site safety inspections. The offline capability alone saved us countless hours. Our compliance rate jumped from 72% to 96% in just three months.”
Sarah Mitchell
Meridian Construction Group
“The AI-powered defect detection has changed how we work. Our inspectors capture photos and the system flags issues we'd have missed. It's like having an expert reviewer on every site visit.”
James Chen
Pacific Manufacturing Co.
“Rolling out digital checklists across multiple projects gave us instant visibility into recurring safety issues. We now resolve critical findings in hours instead of days.”
Olivia Carter
Northbridge Infrastructure
Ready to Move Structural Inspection Off Paper?
Inspections Across Industries
View All
Which Structural Inspection Checklist Templates Should You Try First?
Get started with inspection and audit checklist templates.
Snagging / Punch List
Snagging Inspection Checklist
Catch defects before handover and generate punch list reports in minutes. Room-by-room finish checks, evidence, and corrective actions.
52,000+GET
Snagging / Punch List
New Build Apartment Snagging Checklist
Pre-handover snagging for new build apartments. Room-by-room finish checks, MEP, and defect tracking before keys.
28,500+GET
Safety Inspection
Scaffolding Inspection Checklist
Utilize this Scaffolding Safety Inspection Checklist to spot hazards, verify stability, and ensure compliance with safety standards before work begins.
19,800+GET
Service Report
Field Service Report Form
Capture job details, measurements, work performed, photos, and sign-offs in one structured field service report form.
14,200+GET
Which Structural Inspection Apps Run on iOS and Android?
Use these apps to run inspections and audits.
Frequently Asked Questions About Structural Inspection Software
What does Structural Inspection Software check on a structural inspection?
Structural Inspection Software runs a structured structural inspection covering connections, bolts, and welds, member alignment and plumb, temporary bracing and stability, bearing and baseplate grouting, and corrosion protection. Each point is captured on mobile with a photo and a reading, and a named inspector signs the round off before it can close. The same template runs on every site, so site managers work to one standard rather than a version that drifts between locations. Every record proves what was checked, when, and by whom, so the evidence is ready long before an assessor asks for it.
How often should a structural inspection be done?
How often structural checks run depends on duty, risk, and the standard you follow. Some are daily or pre-use; others run weekly, monthly, or at a statutory interval. Structural Inspection Software sets the cadence per site, reminds site managers before a round is due, and flags anything overdue automatically. Each completed round is timestamped and signed, so the schedule is provably kept rather than assumed, and you can show exactly when the last check happened for any asset. Site Managers run structural inspections on a phone or tablet with Structural Inspection Software, keeping one record for each structural and site.
Which structural defects matter most, and what happens if they are missed?
The inspection targets the structural failures that matter most: under-torqued or missing bolts, weld defects, member out of plumb, and missing temporary bracing. Left unchecked, a fault such as under-torqued or missing bolts can mean downtime, a safety incident, or a failed audit, so every finding becomes an owned task with a deadline. It stays open until photo proof of the repair is reviewed, and repeat problems are flagged so site managers fix the cause rather than the symptom. Prioritising by severity means the most serious issues are handled first, not whichever was reported loudest.
Which standards does Structural Inspection Software support for structural work?
Structural Inspection Software keeps structural checks aligned to AISC 360, BS EN 1090, and IS 800. The photos and readings each standard expects are required fields, so an incomplete check cannot be closed and a gap is caught before an assessor finds it. When a review is due, site managers export a branded evidence pack built from bolt and weld photo, plumb and alignment note, and erection sign-off, ready to hand over on the spot. Retention and history stay searchable, so proof remains defensible at any point, not only on the day of an audit.
Can teams run structural checks offline and across multiple sites?
Yes. Structural Inspection Software is offline-first: teams complete structural checks on iOS or Android with no signal, capturing bolt and weld photo, plumb and alignment note, and erection sign-off in the field. Each record syncs automatically when the connection returns, with its timestamp intact, and the same template runs on every site. So site managers get a live view of what is complete, overdue, or failing per location, and a weak connection in a plant room or basement never costs a round or loses a photo.
What evidence proves a structural inspection was completed?
Every completed structural inspection carries bolt and weld photo, plumb and alignment note, and erection sign-off, a GPS location, a timestamp, and a named sign-off. Because the evidence is captured during the round rather than typed up afterwards, site managers can show exactly what was checked, when, and by whom. When an assessor or client asks, the record exports in seconds as a branded PDF or a searchable history, so proof never depends on someone remembering where a photo was saved or which folder holds last quarter's records.
Last updated: