Take a Photo. AI Fills the Form
Your inspector takes a photo of any asset or defect. AI reads it and fills the inspection form automatically. No typing. No manual entry.
Safety & Compliance
Working at Height InspectionSoftware
Run working at height inspection in the field, capture photo evidence, log defects, assign corrective actions, and keep a complete, provable inspection history, all in one workflow.
InspectWrk is the software we provide to run this inspection workflow. It is mobile-first, offline-capable, and built so every record holds up as evidence.
Works OfflineiOS & AndroidFree Setup & Onboarding
4.5/5TrustpilotBased on 3,987 reviews
The problem this software solves
Defective scaffold or ladder
Reported by voice or chat, defective scaffold or ladder is caught late and logged with no evidence tied to the asset.
Uninspected MEWP
Uninspected MEWP goes unrecorded between rounds, so there is no proof it was found, owned, or fixed.
Faulty fall-arrest equipment
On a manual round faulty fall-arrest equipment is easy to miss, and hard to defend to an auditor after the fact.
Missing edge protection
Missing edge protection lands in a photo thread with no owner, deadline, or audit trail behind it.
How the software solves it
InspectWrk runs the whole working at height inspection cycle on one mobile system, from the scan to the signed-off report. Here is the loop your team follows.
- 1
Inspect
Open the right working at height checklist by scanning the asset or location QR tag.
- 2
Capture
Record photos, readings, and signatures, offline where signal is poor.
- 3
Find
AI flags likely defects from the photo and the inspector confirms or overrides.
- 4
Correct
A failed item becomes an owned action with a severity and a deadline.
- 5
Verify
The finding stays open until a named approver signs off proof of the fix.
- 6
Report
A branded report generates on close-out and dashboards update across sites.
Workflow
How Does a Working at Height Inspection Cycle Run from Field Capture to Audit-Ready Reporting?
The inspection workflow, end to end: Plan → Inspect → Capture evidence → Record findings → Correct → Re-inspect → Report. Every step happens on one system, so nothing falls between the field and the office.
- 1
Configure the Work at Height Template
Your controls become a mobile template with required photos and readings on access equipment and scaffolds, ladders and MEWPs, fall-arrest and anchor points, edge protection and guardrails, and permit to work and rescue plan, aligned to Work at Height Regulations, LOLER, and ISO 45001, so every site works to the same standard from day one.
- 2
Capture the Check in the Field
Field teams complete the work at height inspection on iOS or Android, offline where signal is poor, recording equipment inspection tag, anchor-point record, and permit photo against each point before a named sign-off can close the round.
- 3
Route Findings to Verified Closure
A failed item such as defective scaffold or ladder becomes an owned task with a severity and a deadline, and it stays open until photo proof of the fix is reviewed, so defects do not resurface unnoticed.
- 4
Report Performance
Every check feeds live dashboards and branded exports, so safety officers and supervisors see completion, overdue actions, and risk per site without assembling a report by hand.
Capabilities
What the software handles for working at height inspection
The capabilities that matter for this workflow, and what your team can do with each one.
Programme Scheduling and Statutory Clocks
Across multi-site working at height inspection rounds, working At Height Inspection cadence is enforced per asset: the next check is booked the moment the last one closes, so nothing silently slips off the plan.
Structured Field Capture
Where working at height inspection evidence has to hold up, required-field working at height inspection capture means no skipped questions and no missing evidence, even when the round is rushed.
AI-assisted Evidence Capture
On every working at height inspection cycle, AI assists working at height inspection capture by reading photos for common faults, so field teams confirm rather than transcribe.
Portfolio Dashboards
For HSE & Safety teams running working at height inspection, operations Directors see working at height inspection completion, overdue actions, and risk hotspots across the HSE & Safety portfolio without assembling a report.
Audit-ready Exports
In HSE & Safety working at height inspection operations, branded PDF packs and searchable working at height inspection history assemble HSE & Safety audit evidence for clients, insurers, and regulators in minutes.
Offline-first Mobile Apps
Across the working at height inspection portfolio, no signal, no problem: working at height inspection evidence is captured on-device and uploaded the moment the inspector is back in range.
Coverage
What Does Work at Height Inspection Cover?
Work at height inspection checks access equipment and scaffolds, ladders and MEWPs, fall-arrest and anchor points, edge protection and guardrails, permit to work and rescue plan, and weather and ground conditions. Safety officers and supervisors capture a photo and a reading on each point, offline where signal is poor, and a named reviewer signs the round off, so every work at height record proves what was checked, when, and by whom, and stays aligned to Work at Height Regulations, LOLER, and ISO 45001.
What Gets Checked
- Access equipment and scaffolds
- Ladders and MEWPs
- Fall-arrest and anchor points
- Edge protection and guardrails
- Permit to work and rescue plan
- Weather and ground conditions
Common Defects It Surfaces
- Defective scaffold or ladder
- Uninspected MEWP
- Faulty fall-arrest equipment
- Missing edge protection
- No rescue plan in place
Evidence Captured
- Equipment inspection tag
- Anchor-point record
- Permit photo
Records align toWork at Height RegulationsLOLERISO 45001
One Platform. Mobile-First. AI-Powered.
Manage every checklist in one connected workspace, capture evidence on mobile at the point of work, and let AI turn field inputs into clear, stakeholder-ready reports in minutes.
Collaborate
Collaborate with your team anytime, anywhere
See which checklists your team has in progress across every site, jump into the same inspection with one tap, and keep field, supervisor, and back-office views in sync without sending screenshots on WhatsApp.
- Organise inspection data by site, team, and date
- Assign checks to the inspector or vendor responsible
- Track completion across every location in one view
- Keep field and back-office in sync in real time
- Comment on findings without leaving the inspection
Custom Reports
Custom reports that guide your decision making
Every team reports differently. Build the report your operations, quality, or compliance leads actually want to read, share it as a branded PDF, and schedule delivery to the stakeholders who need it.
- Branded PDF and CSV export from any completed inspection
- Schedule weekly or monthly delivery to managers and clients
- Share to email, Drive, Teams, or Slack in one click
- Filter findings by site, severity, or corrective-action status
Powerful Analytics
Analyse your inspection data with confidence
See completion, pass rate, and recurring findings across every checklist and every site, without pulling spreadsheets together at the end of the month.
AI-Powered Features for Your Field Workflows
Everything your field team does on paper, InspectWrk does automatically: faster, more accurate, and without the admin.
Speak. AI Writes It Down.
Inspectors speak their observations in any language. AI transcribes and fills the form in real time. Completely hands-free in the field.
Inspections Done. Report Ready.
The moment an inspection is submitted, a branded PDF, Excel, or CSV report generates automatically. No manual work. No waiting.
Connect Your Existing Tools.
InspectWrk integrates with the tools your team already uses, including Zoho, Microsoft 365, and SAP. No double entry.
Live Dashboard. Every Site. Always On.
Your operations team sees completion rates, open issues, and compliance scores across all sites in real time. No chasing updates.
Outcomes
What changes for your team
Safety officers and supervisors
A live view of work at height inspection status across every site, with defensible evidence and no Friday report assembly.
Field teams
Guided work at height checks on mobile with offline capture, so defective scaffold or ladder is caught and logged on the spot.
Compliance stakeholders
Searchable history and Work at Height Regulations-ready exports available on demand.
Who it's for
Operations and site managers
Own performance and audit readiness across sites.
Field teams and inspectors
Complete guided checks in the field, offline where needed.
QHSE and compliance teams
Retrieve evidence the moment an auditor or client asks.
Multi-site operations leaders
Compare sites and spot recurring risk without spreadsheets.
HSE & Safety teams
Standardise on one workflow across every location.
Fits how your team already works
Your systems of record
System of record
ERP / WMS / CMMS · Existing spreadsheets · Current reporting
InspectWrk
Inspection and evidence layer
Inspections · Condition evidence · Corrective actions · Compliance clocks
Managers, clients, and auditors
Outputs
Live dashboards · Evidence packs · Audit-ready reports
Comparison
Paper and spreadsheets vs InspectWrk
Where paper and spreadsheets fall short against InspectWrk on the working at height inspection job.
| Capability | Paper / spreadsheets | With InspectWrk |
|---|---|---|
| Inspection execution | Checks like access equipment and scaffolds are run on paper or from memory, so coverage and cadence vary by inspector and shift. | Guided working at height templates run the same way every time, with required fields and photos before sign-off. |
| Evidence capture | Photos sit on personal phones and in chat threads with no link to the asset or the check. | Evidence attaches to the record at the point of work, with inspector, timestamp, and location. |
| Defect identification | A fault such as defective scaffold or ladder is spotted late or missed entirely between rounds. | AI surfaces likely defects from the photo and the inspector confirms the finding on the spot. |
| Corrective action | Failed items are noted but ownership, deadlines, and proof of the fix are unclear. | Each failure becomes a tracked action with an owner, a due date, and photo-verified closure. |
| Reporting | Reports are assembled by hand and Work at Height Regulations evidence is hard to retrieve, days after the round. | Reports generate on close-out aligned to Work at Height Regulations, and managers see status across every site live. |
Rollout
How Should HSE & Safety Teams Pilot Working at Height Inspection Digitally Without Disrupting Operations?
Pilot on one site cluster
Pick one HSE & safety cluster for the initial working at height inspection rollout, confirm the dashboards match what the field sees, then extend template by template.
Scale templates and roles
Roll working at height inspection out site by site, granting contractors scoped access and tying templates to the specific HSE & safety obligations each location carries.
Connect reporting and integrations
Connect working at height inspection evidence to your reporting and asset systems through the API, so Operations Directors get one dashboard and every downstream tool stays in step.
Before You Switch
Common Questions Before You Start
We already run working at height checks on paper. Do we have to change our process?
No. Your existing checklist becomes a mobile template, so the same checks run with photos, timestamps, and named sign-off attached. Only the capture changes.
Will field teams actually use it?
The check runs on the device they already carry, works offline where signal drops, and opens the right checklist from a QR scan, so there is no typing from memory.
What happens when a defect is found?
It becomes an owned action with a severity and a deadline, and stays open until a named approver verifies the fix with photo proof.
Reviews From Real People
4.5/5TrustpilotBased on 3,987 reviews
What our
customers are
saying
“InspectWrk transformed how we manage site safety inspections. The offline capability alone saved us countless hours. Our compliance rate jumped from 72% to 96% in just three months.”
Sarah Mitchell
Meridian Construction Group
“The AI-powered defect detection has changed how we work. Our inspectors capture photos and the system flags issues we'd have missed. It's like having an expert reviewer on every site visit.”
James Chen
Pacific Manufacturing Co.
“Rolling out digital checklists across multiple projects gave us instant visibility into recurring safety issues. We now resolve critical findings in hours instead of days.”
Olivia Carter
Northbridge Infrastructure
Ready to Move Working at Height Inspection Off Paper?
Inspections Across Industries
View All
Which Working at Height Inspection Checklist Templates Should You Try First?
Get started with inspection and audit checklist templates.
Safety
Safety Inspection Checklist
Safety inspections with hazard identification, corrective actions, and compliance reporting. Offline capture and evidence.
52,100+GET
Incident Reporting
Incident Report Form
Report incidents and near-misses with details, photos, location, and timeline. Ready for safety or quality review.
26,700+GET
Electrical Safety
Arc Flash Label Inspection Checklist
Verify arc-flash labels on electrical equipment: presence, visibility, legibility, equipment identification, voltage and incident-energy information, PPE data, and label condition.
9,100+GET
Electrical Safety
Grounding & Bonding Inspection Checklist
Inspect grounding and bonding systems: grounding conductors and electrodes, bonding connections, equipment grounding, continuity, corrosion, and panel connections.
10,200+GET
Frequently Asked Questions About Working at Height Inspection Software
What does Working At Height Inspection Software check in work at height inspection?
Working At Height Inspection Software runs work at height inspection covering access equipment and scaffolds, ladders and MEWPs, fall-arrest and anchor points, edge protection and guardrails, and permit to work and rescue plan. Each point is captured on mobile with a photo, and a reading where one applies, then a named reviewer signs the round off before it can close. The same template runs on every site, so safety officers and supervisors get one consistent standard across the work at height portfolio, and every record proves what was checked, when, and by whom.
Which work at height problems does Working At Height Inspection Software help catch?
The programme targets the failures that matter most: defective scaffold or ladder, uninspected MEWP, faulty fall-arrest equipment, and missing edge protection. When a check fails, it becomes an assigned task with an owner, a severity, and a deadline, and it stays open until photo proof of the fix is reviewed. Repeat failures are flagged, so teams fix the cause rather than the symptom. For safety officers and supervisors, that turns defective scaffold or ladder from a note lost in a chat thread into a tracked action with verified closure across every work at height site.
Which standards does Working At Height Inspection Software support?
Working At Height Inspection Software keeps work at height work aligned to Work at Height Regulations, LOLER, and ISO 45001. The photos, readings, and sign-offs each standard expects are required fields, so an incomplete check cannot close and a gap is caught before an assessor finds it. When a review is due, safety officers and supervisors export a branded pack and a searchable history for the site in scope, built from the live record with equipment inspection tag, anchor-point record, and permit photo rather than rebuilt from folders and email. That keeps evidence defensible at any time, not only in the week before an audit.
Can teams run work at height checks offline and across multiple sites?
Yes. Field teams complete work at height checks on iOS or Android with no signal, capturing equipment inspection tag, anchor-point record, and permit photo in the field, and each record syncs when the connection returns with its timestamp and author intact. Because the same template runs on every site, safety officers and supervisors get one consistent standard across the work at height portfolio and a live view of what is complete, overdue, or failing per location, without waiting for a site to email a report.
How do teams roll out Working At Height Inspection Software?
Most work at height teams start on one template and a single cluster of sites, watching completion and closure time from day one. The checks that cause the most chasing today go first: access equipment and scaffolds, ladders and MEWPs, fall-arrest and anchor points, edge protection and guardrails, and permit to work and rescue plan. Once field teams trust the digital record and findings reach verified closure, the same template scales across the estate, and new sites inherit the approved programme on day one so the standard does not drift. Safety officers and supervisors keep one view of the work across every location as the portfolio grows.
Does Working At Height Inspection Software work with a CMMS or asset register?
Working At Height Inspection Software runs alongside the systems you already use. Findings and readings can flow into a CMMS, ERP, or asset register through the API, so those systems hold verified field data instead of re-keyed notes. It owns the part they were never built for: offline capture, photo evidence, and a fast audit pack built from equipment inspection tag, anchor-point record, and permit photo. Teams keep work orders and finance where they are, and add the work at height inspection layer where the evidence is captured, so the record and the work order finally agree.
Last updated: