Take a Photo. AI Fills the Form
Your inspector takes a photo of any asset or defect. AI reads it and fills the inspection form automatically. No typing. No manual entry.
Inspection & Field Operations
SCADA InspectionSoftware
Run SCADA inspection in the field, capture photo evidence, log defects, assign corrective actions, and keep a complete, provable inspection history, all in one workflow.
InspectWrk is the software we provide to run this inspection workflow. It is mobile-first, offline-capable, and built so every record holds up as evidence.
Works OfflineiOS & AndroidFree Setup & Onboarding
4.5/5TrustpilotBased on 3,987 reviews
The problem this software solves
RTU or PLC fault
Reported by voice or chat, RTU or PLC fault is caught late and logged with no evidence tied to the asset.
Comms loss or no redundancy
Comms loss or no redundancy goes unrecorded between rounds, so there is no proof it was found, owned, or fixed.
Alarm flood or wrong setpoint
On a manual round alarm flood or wrong setpoint is easy to miss, and hard to defend to an auditor after the fact.
Logging gap
Logging gap lands in a photo thread with no owner, deadline, or audit trail behind it.
How the software solves it
InspectWrk runs the whole SCADA inspection cycle on one mobile system, from the scan to the signed-off report. Here is the loop your team follows.
- 1
Inspect
Open the right SCADA checklist by scanning the asset or location QR tag.
- 2
Capture
Record photos, readings, and signatures, offline where signal is poor.
- 3
Find
AI flags likely defects from the photo and the inspector confirms or overrides.
- 4
Correct
A failed item becomes an owned action with a severity and a deadline.
- 5
Verify
The finding stays open until a named approver signs off proof of the fix.
- 6
Report
A branded report generates on close-out and dashboards update across sites.
Workflow
How Does a SCADA Inspection Cycle Run from Field Capture to Audit-Ready Reporting?
The inspection workflow, end to end: Plan → Inspect → Capture evidence → Record findings → Correct → Re-inspect → Report. Every step happens on one system, so nothing falls between the field and the office.
- 1
Configure the SCADA Inspection Template
Your SCADA controls become a mobile template with required photos and readings on RTU and PLC status, communications and redundancy, alarms and setpoints, data logging and historian, and access control and cybersecurity, aligned to IEC 62443 and ISA-95, so every site inspects to the same standard from day one.
- 2
Capture the SCADA Check in the Field
Inspectors complete the SCADA inspection on iOS or Android, offline where signal is poor, recording system status screenshot, alarm log note, and access record against each point before a named sign-off can close the round.
- 3
Route SCADA Findings to Verified Closure
A failed item such as rtu or plc fault becomes an owned task with a severity and a deadline, and stays open until photo proof of the fix is reviewed, so SCADA defects do not resurface unnoticed.
- 4
Report SCADA Performance
On every SCADA inspection cycle, every SCADA inspection feeds live dashboards and branded exports, so fm engineering managers see completion, overdue actions, and risk per site without assembling a report by hand.
Capabilities
What the software handles for SCADA inspection
The capabilities that matter for this workflow, and what your team can do with each one.
Programme Scheduling and Statutory Clocks
For SCADA inspection field teams, recurring SCADA inspection cycles auto-schedule by asset and site, and overdue clocks escalate before they become a Facilities Management compliance gap.
Structured Field Capture
Across multi-site SCADA inspection rounds, SCADA Inspection capture is standardised across every site, so two inspectors record the same thing the same way on the same form.
AI-assisted Evidence Capture
Where SCADA inspection evidence has to hold up, AI photo review turns SCADA inspection evidence into draft findings on the spot, which the inspector accepts, edits, or rejects.
Portfolio Dashboards
On every SCADA inspection cycle, portfolio dashboards surface where SCADA inspection programmes are slipping, so FM Engineering Managers act before a client or regulator does.
Audit-ready Exports
For Facilities Management teams running SCADA inspection, searchable SCADA inspection records mean any past check is retrievable instantly, so FM Engineering Managers stop rebuilding history from drives.
Offline-first Mobile Apps
In Facilities Management SCADA inspection operations, offline-first capture keeps SCADA inspection rounds moving in lifts, basements, and remote Facilities Management sites, then reconciles on reconnect.
Coverage
What Does a SCADA Inspection Cover?
A SCADA inspection covers RTU and PLC status, communications and redundancy, alarms and setpoints, data logging and historian, and access control and cybersecurity. Fm engineering managers capture a photo and a reading on each SCADA point. They work offline where signal is poor, then sign the SCADA round off. So every SCADA record proves what was checked, when, and by whom.
What Gets Checked
- RTU and PLC status
- Communications and redundancy
- Alarms and setpoints
- Data logging and historian
- Access control and cybersecurity
Common Defects It Surfaces
- RTU or PLC fault
- Comms loss or no redundancy
- Alarm flood or wrong setpoint
- Logging gap
- Weak access control
Evidence Captured
- System status screenshot
- Alarm log note
- Access record
Records align toIEC 62443ISA-95
One Platform. Mobile-First. AI-Powered.
Manage every checklist in one connected workspace, capture evidence on mobile at the point of work, and let AI turn field inputs into clear, stakeholder-ready reports in minutes.
Collaborate
Collaborate with your team anytime, anywhere
See which checklists your team has in progress across every site, jump into the same inspection with one tap, and keep field, supervisor, and back-office views in sync without sending screenshots on WhatsApp.
- Organise inspection data by site, team, and date
- Assign checks to the inspector or vendor responsible
- Track completion across every location in one view
- Keep field and back-office in sync in real time
- Comment on findings without leaving the inspection
Custom Reports
Custom reports that guide your decision making
Every team reports differently. Build the report your operations, quality, or compliance leads actually want to read, share it as a branded PDF, and schedule delivery to the stakeholders who need it.
- Branded PDF and CSV export from any completed inspection
- Schedule weekly or monthly delivery to managers and clients
- Share to email, Drive, Teams, or Slack in one click
- Filter findings by site, severity, or corrective-action status
Powerful Analytics
Analyse your inspection data with confidence
See completion, pass rate, and recurring findings across every checklist and every site, without pulling spreadsheets together at the end of the month.
AI-Powered Features for Your Field Workflows
Everything your field team does on paper, InspectWrk does automatically: faster, more accurate, and without the admin.
Speak. AI Writes It Down.
Inspectors speak their observations in any language. AI transcribes and fills the form in real time. Completely hands-free in the field.
Inspections Done. Report Ready.
The moment an inspection is submitted, a branded PDF, Excel, or CSV report generates automatically. No manual work. No waiting.
Connect Your Existing Tools.
InspectWrk integrates with the tools your team already uses, including Zoho, Microsoft 365, and SAP. No double entry.
Live Dashboard. Every Site. Always On.
Your operations team sees completion rates, open issues, and compliance scores across all sites in real time. No chasing updates.
Outcomes
What changes for your team
FM Engineering Managers
A live view of SCADA inspection status across every site, with defensible evidence and no Friday report assembly.
Field teams
Guided SCADA checks on mobile with offline capture, so rtu or plc fault is caught and logged on the spot.
Compliance stakeholders
Searchable SCADA history and IEC 62443-ready exports available on demand.
Who it's for
Operations and site managers
Own performance and audit readiness across sites.
Field teams and inspectors
Complete guided checks in the field, offline where needed.
QHSE and compliance teams
Retrieve evidence the moment an auditor or client asks.
Multi-site operations leaders
Compare sites and spot recurring risk without spreadsheets.
Facilities Management teams
Standardise on one workflow across every location.
Fits how your team already works
Your systems of record
System of record
ERP / WMS / CMMS · Existing spreadsheets · Current reporting
InspectWrk
Inspection and evidence layer
Inspections · Condition evidence · Corrective actions · Compliance clocks
Managers, clients, and auditors
Outputs
Live dashboards · Evidence packs · Audit-ready reports
Comparison
Paper and spreadsheets vs InspectWrk
Where paper and spreadsheets fall short against InspectWrk on the SCADA inspection job.
| Capability | Paper / spreadsheets | With InspectWrk |
|---|---|---|
| Inspection execution | Checks like RTU and PLC status are run on paper or from memory, so coverage and cadence vary by inspector and shift. | Guided SCADA templates run the same way every time, with required fields and photos before sign-off. |
| Evidence capture | Photos sit on personal phones and in chat threads with no link to the asset or the check. | Evidence attaches to the record at the point of work, with inspector, timestamp, and location. |
| Defect identification | A fault such as RTU or PLC fault is spotted late or missed entirely between rounds. | AI surfaces likely defects from the photo and the inspector confirms the finding on the spot. |
| Corrective action | Failed items are noted but ownership, deadlines, and proof of the fix are unclear. | Each failure becomes a tracked action with an owner, a due date, and photo-verified closure. |
| Reporting | Reports are assembled by hand and IEC 62443 evidence is hard to retrieve, days after the round. | Reports generate on close-out aligned to IEC 62443, and managers see status across every site live. |
Rollout
How Should Facilities Management Teams Pilot SCADA Inspection Digitally Without Disrupting Operations?
Pilot on one site cluster
Start narrow with a pilot SCADA inspection programme on a few sites, so FM Engineering Managers can validate evidence quality and correction speed against the old paper baseline.
Scale templates and roles
Extend SCADA inspection access to contractors and in-house crews with role-based permissions, and map each template to your facilities management standards and statutory duties.
Connect reporting and integrations
Publish SCADA inspection performance to portfolio dashboards, export branded audit packs, and integrate with the facilities management systems that own work orders and records.
Before You Switch
Common Questions Before You Start
We already run SCADA checks on paper. Do we have to change our process?
No. Your existing checklist becomes a mobile template, so the same checks run with photos, timestamps, and named sign-off attached. Only the capture changes.
Will field teams actually use it?
The check runs on the device they already carry, works offline where signal drops, and opens the right checklist from a QR scan, so there is no typing from memory.
What happens when a defect is found?
It becomes an owned action with a severity and a deadline, and stays open until a named approver verifies the fix with photo proof.
Reviews From Real People
4.5/5TrustpilotBased on 3,987 reviews
What our
customers are
saying
“InspectWrk transformed how we manage site safety inspections. The offline capability alone saved us countless hours. Our compliance rate jumped from 72% to 96% in just three months.”
Sarah Mitchell
Meridian Construction Group
“The AI-powered defect detection has changed how we work. Our inspectors capture photos and the system flags issues we'd have missed. It's like having an expert reviewer on every site visit.”
James Chen
Pacific Manufacturing Co.
“Rolling out digital checklists across multiple projects gave us instant visibility into recurring safety issues. We now resolve critical findings in hours instead of days.”
Olivia Carter
Northbridge Infrastructure
Ready to Move SCADA Inspection Off Paper?
Inspections Across Industries
View All
Which SCADA Inspection Checklist Templates Should You Try First?
Get started with inspection and audit checklist templates.
Inspections
Site Inspection Checklist
Standard site-level inspections for construction, safety, and compliance. Capture conditions, photos, and follow-ups in one place.
41,000+GET
Asset Management
Asset Inspection Checklist
Inspect assets and equipment: condition, location, photos, and maintenance history. Track condition over time.
28,900+GET
Work Orders
Work Order Checklist
Complete work orders with checklist items, photos, and sign-off. Track completion and proof of work.
31,800+GET
Maintenance
Maintenance Checklist
Preventive and corrective maintenance inspections. Log repairs, parts, and condition with photos and follow-ups.
27,400+GET
Which SCADA Inspection Apps Run on iOS and Android?
Use these apps to run inspections and audits.
Frequently Asked Questions About SCADA Inspection Software
What does SCADA Inspection Software check on a SCADA inspection?
SCADA Inspection Software runs a structured SCADA inspection covering RTU and PLC status, communications and redundancy, alarms and setpoints, data logging and historian, and access control and cybersecurity. Each point is captured on mobile with a photo and a reading, and a named inspector signs the round off before it can close. The same template runs on every site, so fm engineering managers work to one standard rather than a version that drifts between locations. Every record proves what was checked, when, and by whom, so the evidence is ready long before an assessor asks for it.
How often should a SCADA inspection be done?
How often SCADA checks run depends on duty, risk, and the standard you follow. Some are daily or pre-use; others run weekly, monthly, or at a statutory interval. SCADA Inspection Software sets the cadence per site, reminds fm engineering managers before a round is due, and flags anything overdue automatically. Each completed round is timestamped and signed, so the schedule is provably kept rather than assumed, and you can show exactly when the last check happened for any asset. SCADA Inspection Software moves SCADA inspections off paper, WhatsApp, and spreadsheets into one timestamped record per SCADA.
Which SCADA defects matter most, and what happens if they are missed?
The inspection targets the SCADA failures that matter most: RTU or PLC fault, comms loss or no redundancy, alarm flood or wrong setpoint, and logging gap. Left unchecked, a fault such as rtu or plc fault can mean downtime, a safety incident, or a failed audit, so every finding becomes an owned task with a deadline. It stays open until photo proof of the repair is reviewed, and repeat problems are flagged so fm engineering managers fix the cause rather than the symptom. Prioritising by severity means the most serious issues are handled first, not whichever was reported loudest.
Which standards does SCADA Inspection Software support for SCADA work?
SCADA Inspection Software keeps SCADA checks aligned to IEC 62443 and ISA-95. The photos and readings each standard expects are required fields, so an incomplete check cannot be closed and a gap is caught before an assessor finds it. When a review is due, fm engineering managers export a branded evidence pack built from system status screenshot, alarm log note, and access record, ready to hand over on the spot. Retention and history stay searchable, so proof remains defensible at any point, not only on the day of an audit.
Can teams run SCADA checks offline and across multiple sites?
Yes. SCADA Inspection Software is offline-first: teams complete SCADA checks on iOS or Android with no signal, capturing system status screenshot, alarm log note, and access record in the field. Each record syncs automatically when the connection returns, with its timestamp intact, and the same template runs on every site. So fm engineering managers get a live view of what is complete, overdue, or failing per location, and a weak connection in a plant room or basement never costs a round or loses a photo.
What evidence proves a SCADA inspection was completed?
Every completed SCADA inspection carries system status screenshot, alarm log note, and access record, a GPS location, a timestamp, and a named sign-off. Because the evidence is captured during the round rather than typed up afterwards, fm engineering managers can show exactly what was checked, when, and by whom. When an assessor or client asks, the record exports in seconds as a branded PDF or a searchable history, so proof never depends on someone remembering where a photo was saved or which folder holds last quarter's records.
Last updated: