Take a Photo. AI Fills the Form
Your inspector takes a photo of any asset or defect. AI reads it and fills the inspection form automatically. No typing. No manual entry.
Inspection & Field Operations
SCADA MaintenanceSoftware
Schedule SCADA maintenance, complete condition checks from the field, raise work orders from failed items, and keep a full asset and maintenance history, all in one workflow.
InspectWrk is the software we provide to run this maintenance round workflow. It is mobile-first, offline-capable, and built so every record holds up as evidence.
Works OfflineiOS & AndroidFree Setup & Onboarding
4.5/5TrustpilotBased on 3,987 reviews
The problem this software solves
RTU or PLC fault
Reported by voice or chat, RTU or PLC fault is caught late and logged with no evidence tied to the asset.
Comms loss or no redundancy
Comms loss or no redundancy goes unrecorded between rounds, so there is no proof it was found, owned, or fixed.
Alarm flood or wrong setpoint
On a manual round alarm flood or wrong setpoint is easy to miss, and hard to defend to an auditor after the fact.
Logging gap
Logging gap lands in a photo thread with no owner, deadline, or audit trail behind it.
How the software solves it
InspectWrk runs the whole SCADA maintenance inspection cycle on one mobile system, from the scan to the signed-off report. Here is the loop your team follows.
- 1
Inspect
Open the right SCADA maintenance checklist by scanning the asset or location QR tag.
- 2
Capture
Record photos, readings, and signatures, offline where signal is poor.
- 3
Find
AI flags likely defects from the photo and the inspector confirms or overrides.
- 4
Correct
A failed item becomes an owned action with a severity and a deadline.
- 5
Verify
The finding stays open until a named approver signs off proof of the fix.
- 6
Report
A branded report generates on close-out and dashboards update across sites.
Workflow
How Does a SCADA Maintenance Cycle Run from Field Capture to Audit-Ready Reporting?
The maintenance round workflow, end to end: Register asset → Schedule → Perform work → Record findings → Raise work order → Verify → History. Every step happens on one system, so nothing falls between the field and the office.
- 1
Configure the SCADA Maintenance Template
On SCADA maintenance programmes, your SCADA controls become a mobile template with required photos and readings on RTU and PLC status, communications and redundancy, alarms and setpoints, data logging and historian, and access control and cybersecurity, aligned to IEC 62443 and ISA-95, so every site inspects to the same standard from day one.
- 2
Capture the SCADA Check in the Field
Inspectors complete the SCADA maintenance on iOS or Android, offline where signal is poor, recording system status screenshot, alarm log note, and access record against each point before a named sign-off can close the round.
- 3
Route SCADA Findings to Verified Closure
Across multi-site SCADA maintenance rounds, A failed item such as rtu or plc fault becomes an owned task with a severity and a deadline, and stays open until photo proof of the fix is reviewed, so SCADA defects do not resurface unnoticed.
- 4
Report SCADA Performance
Where SCADA maintenance evidence has to hold up, every SCADA maintenance feeds live dashboards and branded exports, so fm engineering managers see completion, overdue actions, and risk per site without assembling a report by hand.
Capabilities
What the software handles for SCADA maintenance
The capabilities that matter for this workflow, and what your team can do with each one.
Programme Scheduling and Statutory Clocks
Across multi-site SCADA maintenance rounds, SCADA Maintenance cadence is enforced per asset: the next check is booked the moment the last one closes, so nothing silently slips off the plan.
Structured Field Capture
Where SCADA maintenance evidence has to hold up, required-field SCADA maintenance capture means no skipped questions and no missing evidence, even when the round is rushed.
AI-assisted Evidence Capture
On every SCADA maintenance cycle, on-device AI flags likely defects in SCADA maintenance photos and pre-fills findings, so inspectors type less and miss less in the field.
Portfolio Dashboards
For Facilities Management teams running SCADA maintenance, one screen shows every site's SCADA maintenance status, so FM Engineering Managers spot the failing location before it becomes a Facilities Management incident.
Audit-ready Exports
In Facilities Management SCADA maintenance operations, SCADA Maintenance evidence exports as a regulator-ready pack with photos and sign-offs intact, filtered to the site under review.
Offline-first Mobile Apps
Across the SCADA maintenance portfolio, weak-signal sites stop being an excuse for missing SCADA maintenance evidence, because capture and sync are decoupled on mobile.
Coverage
What Does a SCADA Maintenance Cover?
A SCADA maintenance round covers RTU and PLC status, communications and redundancy, alarms and setpoints, data logging and historian, and access control and cybersecurity. Each SCADA task is scheduled per asset and done on mobile with photo evidence. It is logged to the SCADA service history. So SCADA upkeep is provable, not assumed.
What Gets Checked
- RTU and PLC status
- Communications and redundancy
- Alarms and setpoints
- Data logging and historian
- Access control and cybersecurity
Common Defects It Surfaces
- RTU or PLC fault
- Comms loss or no redundancy
- Alarm flood or wrong setpoint
- Logging gap
- Weak access control
Evidence Captured
- System status screenshot
- Alarm log note
- Access record
Records align toIEC 62443ISA-95
One Platform. Mobile-First. AI-Powered.
Manage every checklist in one connected workspace, capture evidence on mobile at the point of work, and let AI turn field inputs into clear, stakeholder-ready reports in minutes.
Collaborate
Collaborate with your team anytime, anywhere
See which checklists your team has in progress across every site, jump into the same inspection with one tap, and keep field, supervisor, and back-office views in sync without sending screenshots on WhatsApp.
- Organise inspection data by site, team, and date
- Assign checks to the inspector or vendor responsible
- Track completion across every location in one view
- Keep field and back-office in sync in real time
- Comment on findings without leaving the inspection
Custom Reports
Custom reports that guide your decision making
Every team reports differently. Build the report your operations, quality, or compliance leads actually want to read, share it as a branded PDF, and schedule delivery to the stakeholders who need it.
- Branded PDF and CSV export from any completed inspection
- Schedule weekly or monthly delivery to managers and clients
- Share to email, Drive, Teams, or Slack in one click
- Filter findings by site, severity, or corrective-action status
Powerful Analytics
Analyse your inspection data with confidence
See completion, pass rate, and recurring findings across every checklist and every site, without pulling spreadsheets together at the end of the month.
AI-Powered Features for Your Field Workflows
Everything your field team does on paper, InspectWrk does automatically: faster, more accurate, and without the admin.
Speak. AI Writes It Down.
Inspectors speak their observations in any language. AI transcribes and fills the form in real time. Completely hands-free in the field.
Inspections Done. Report Ready.
The moment an inspection is submitted, a branded PDF, Excel, or CSV report generates automatically. No manual work. No waiting.
Connect Your Existing Tools.
InspectWrk integrates with the tools your team already uses, including Zoho, Microsoft 365, and SAP. No double entry.
Live Dashboard. Every Site. Always On.
Your operations team sees completion rates, open issues, and compliance scores across all sites in real time. No chasing updates.
Outcomes
What changes for your team
FM Engineering Managers
A live view of SCADA maintenance status across every site, with defensible evidence and no Friday report assembly.
Field teams
Guided SCADA checks on mobile with offline capture, so rtu or plc fault is caught and logged on the spot.
Compliance stakeholders
Searchable SCADA history and IEC 62443-ready exports available on demand.
Who it's for
Operations and site managers
Own performance and audit readiness across sites.
Field teams and inspectors
Complete guided checks in the field, offline where needed.
QHSE and compliance teams
Retrieve evidence the moment an auditor or client asks.
Multi-site operations leaders
Compare sites and spot recurring risk without spreadsheets.
Facilities Management teams
Standardise on one workflow across every location.
Fits how your team already works
Your systems of record
System of record
ERP / WMS / CMMS · Existing spreadsheets · Current reporting
InspectWrk
Inspection and evidence layer
Inspections · Condition evidence · Corrective actions · Compliance clocks
Managers, clients, and auditors
Outputs
Live dashboards · Evidence packs · Audit-ready reports
Comparison
Paper and spreadsheets vs InspectWrk
Where paper and spreadsheets fall short against InspectWrk on the SCADA maintenance inspection job.
| Capability | Paper / spreadsheets | With InspectWrk |
|---|---|---|
| Inspection execution | Checks like RTU and PLC status are run on paper or from memory, so coverage and cadence vary by inspector and shift. | Guided SCADA maintenance templates run the same way every time, with required fields and photos before sign-off. |
| Evidence capture | Photos sit on personal phones and in chat threads with no link to the asset or the check. | Evidence attaches to the record at the point of work, with inspector, timestamp, and location. |
| Defect identification | A fault such as RTU or PLC fault is spotted late or missed entirely between rounds. | AI surfaces likely defects from the photo and the inspector confirms the finding on the spot. |
| Corrective action | Failed items are noted but ownership, deadlines, and proof of the fix are unclear. | Each failure becomes a tracked action with an owner, a due date, and photo-verified closure. |
| Reporting | Reports are assembled by hand and IEC 62443 evidence is hard to retrieve, days after the round. | Reports generate on close-out aligned to IEC 62443, and managers see status across every site live. |
Rollout
How Should Facilities Management Teams Pilot SCADA Maintenance Digitally Without Disrupting Operations?
Pilot on one site cluster
Pick one facilities management cluster for the initial SCADA maintenance rollout, confirm the dashboards match what the field sees, then extend template by template.
Scale templates and roles
Roll SCADA maintenance out site by site, granting contractors scoped access and tying templates to the specific facilities management obligations each location carries.
Connect reporting and integrations
Turn on live SCADA maintenance reporting for FM Engineering Managers, and route readings and defects into the CMMS or compliance system of record so nothing is re-keyed.
Before You Switch
Common Questions Before You Start
We already run SCADA maintenance checks on paper. Do we have to change our process?
No. Your existing checklist becomes a mobile template, so the same checks run with photos, timestamps, and named sign-off attached. Only the capture changes.
Will field teams actually use it?
The check runs on the device they already carry, works offline where signal drops, and opens the right checklist from a QR scan, so there is no typing from memory.
What happens when a defect is found?
It becomes an owned action with a severity and a deadline, and stays open until a named approver verifies the fix with photo proof.
Reviews From Real People
4.5/5TrustpilotBased on 3,987 reviews
What our
customers are
saying
“InspectWrk transformed how we manage site safety inspections. The offline capability alone saved us countless hours. Our compliance rate jumped from 72% to 96% in just three months.”
Sarah Mitchell
Meridian Construction Group
“The AI-powered defect detection has changed how we work. Our inspectors capture photos and the system flags issues we'd have missed. It's like having an expert reviewer on every site visit.”
James Chen
Pacific Manufacturing Co.
“Rolling out digital checklists across multiple projects gave us instant visibility into recurring safety issues. We now resolve critical findings in hours instead of days.”
Olivia Carter
Northbridge Infrastructure
Ready to Move SCADA Maintenance Off Paper?
Inspections Across Industries
View All
Which SCADA Maintenance Checklist Templates Should You Try First?
Get started with inspection and audit checklist templates.
Inspections
Site Inspection Checklist
Standard site-level inspections for construction, safety, and compliance. Capture conditions, photos, and follow-ups in one place.
41,000+GET
Asset Management
Asset Inspection Checklist
Inspect assets and equipment: condition, location, photos, and maintenance history. Track condition over time.
28,900+GET
Work Orders
Work Order Checklist
Complete work orders with checklist items, photos, and sign-off. Track completion and proof of work.
31,800+GET
Maintenance
Maintenance Checklist
Preventive and corrective maintenance inspections. Log repairs, parts, and condition with photos and follow-ups.
27,400+GET
Frequently Asked Questions About SCADA Maintenance Software
What does SCADA Maintenance Software check on a SCADA maintenance?
SCADA Maintenance Software runs planned SCADA maintenance covering RTU and PLC status, communications and redundancy, alarms and setpoints, data logging and historian, and access control and cybersecurity. Each task is scheduled per asset and completed on mobile with photo evidence, then logged to the service history, so fm engineering managers can prove upkeep happened on time. Catching rtu or plc fault on a planned visit avoids a reactive breakdown later. Due dates and overdue tasks surface on the dashboard before a service quietly lapses, which is the common and expensive gap when schedules live in a spreadsheet.
How often should a SCADA maintenance be done?
How often SCADA checks run depends on duty, risk, and the standard you follow. Some are daily or pre-use; others run weekly, monthly, or at a statutory interval. SCADA Maintenance Software sets the cadence per site, reminds fm engineering managers before a round is due, and flags anything overdue automatically. Each completed round is timestamped and signed, so the schedule is provably kept rather than assumed, and you can show exactly when the last check happened for any asset. In facilities management, SCADA Maintenance Software turns approved SCADA checklists into mobile checks field teams complete on any device.
Which SCADA defects matter most, and what happens if they are missed?
The maintenance targets the SCADA failures that matter most: RTU or PLC fault, comms loss or no redundancy, alarm flood or wrong setpoint, and logging gap. Left unchecked, a fault such as rtu or plc fault can mean downtime, a safety incident, or a failed audit, so every finding becomes an owned task with a deadline. It stays open until photo proof of the repair is reviewed, and repeat problems are flagged so fm engineering managers fix the cause rather than the symptom. Prioritising by severity means the most serious issues are handled first, not whichever was reported loudest.
Which standards does SCADA Maintenance Software support for SCADA work?
SCADA Maintenance Software keeps SCADA checks aligned to IEC 62443 and ISA-95. The photos and readings each standard expects are required fields, so an incomplete check cannot be closed and a gap is caught before an assessor finds it. When a review is due, fm engineering managers export a branded evidence pack built from system status screenshot, alarm log note, and access record, ready to hand over on the spot. Retention and history stay searchable, so proof remains defensible at any point, not only on the day of an audit.
Can teams run SCADA checks offline and across multiple sites?
Yes. SCADA Maintenance Software is offline-first: teams complete SCADA checks on iOS or Android with no signal, capturing system status screenshot, alarm log note, and access record in the field. Each record syncs automatically when the connection returns, with its timestamp intact, and the same template runs on every site. So fm engineering managers get a live view of what is complete, overdue, or failing per location, and a weak connection in a plant room or basement never costs a round or loses a photo.
What evidence proves a SCADA maintenance was completed?
Every completed SCADA maintenance carries system status screenshot, alarm log note, and access record, a GPS location, a timestamp, and a named sign-off. Because the evidence is captured during the round rather than typed up afterwards, fm engineering managers can show exactly what was checked, when, and by whom. When an assessor or client asks, the record exports in seconds as a branded PDF or a searchable history, so proof never depends on someone remembering where a photo was saved or which folder holds last quarter's records.
Last updated: